1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * Copyright (C) 2012 Invensense, Inc. 4 */ 5 6 #ifndef INV_MPU_IIO_H_ 7 #define INV_MPU_IIO_H_ 8 9 #include <linux/i2c.h> 10 #include <linux/i2c-mux.h> 11 #include <linux/mutex.h> 12 #include <linux/iio/iio.h> 13 #include <linux/iio/buffer.h> 14 #include <linux/regmap.h> 15 #include <linux/iio/sysfs.h> 16 #include <linux/iio/kfifo_buf.h> 17 #include <linux/iio/trigger.h> 18 #include <linux/iio/triggered_buffer.h> 19 #include <linux/iio/trigger_consumer.h> 20 #include <linux/platform_data/invensense_mpu6050.h> 21 22 /** 23 * struct inv_mpu6050_reg_map - Notable registers. 24 * @sample_rate_div: Divider applied to gyro output rate. 25 * @lpf: Configures internal low pass filter. 26 * @accel_lpf: Configures accelerometer low pass filter. 27 * @user_ctrl: Enables/resets the FIFO. 28 * @fifo_en: Determines which data will appear in FIFO. 29 * @gyro_config: gyro config register. 30 * @accl_config: accel config register 31 * @fifo_count_h: Upper byte of FIFO count. 32 * @fifo_r_w: FIFO register. 33 * @raw_gyro: Address of first gyro register. 34 * @raw_accl: Address of first accel register. 35 * @temperature: temperature register 36 * @int_enable: Interrupt enable register. 37 * @int_status: Interrupt status register. 38 * @pwr_mgmt_1: Controls chip's power state and clock source. 39 * @pwr_mgmt_2: Controls power state of individual sensors. 40 * @int_pin_cfg; Controls interrupt pin configuration. 41 * @accl_offset: Controls the accelerometer calibration offset. 42 * @gyro_offset: Controls the gyroscope calibration offset. 43 * @i2c_if: Controls the i2c interface 44 */ 45 struct inv_mpu6050_reg_map { 46 u8 sample_rate_div; 47 u8 lpf; 48 u8 accel_lpf; 49 u8 user_ctrl; 50 u8 fifo_en; 51 u8 gyro_config; 52 u8 accl_config; 53 u8 fifo_count_h; 54 u8 fifo_r_w; 55 u8 raw_gyro; 56 u8 raw_accl; 57 u8 temperature; 58 u8 int_enable; 59 u8 int_status; 60 u8 pwr_mgmt_1; 61 u8 pwr_mgmt_2; 62 u8 int_pin_cfg; 63 u8 accl_offset; 64 u8 gyro_offset; 65 u8 i2c_if; 66 }; 67 68 /*device enum */ 69 enum inv_devices { 70 INV_MPU6050, 71 INV_MPU6500, 72 INV_MPU6515, 73 INV_MPU6880, 74 INV_MPU6000, 75 INV_MPU9150, 76 INV_MPU9250, 77 INV_MPU9255, 78 INV_ICM20608, 79 INV_ICM20609, 80 INV_ICM20689, 81 INV_ICM20602, 82 INV_ICM20690, 83 INV_IAM20680, 84 INV_NUM_PARTS 85 }; 86 87 /* chip sensors mask: accelerometer, gyroscope, temperature, magnetometer */ 88 #define INV_MPU6050_SENSOR_ACCL BIT(0) 89 #define INV_MPU6050_SENSOR_GYRO BIT(1) 90 #define INV_MPU6050_SENSOR_TEMP BIT(2) 91 #define INV_MPU6050_SENSOR_MAGN BIT(3) 92 93 /** 94 * struct inv_mpu6050_chip_config - Cached chip configuration data. 95 * @clk: selected chip clock 96 * @fsr: Full scale range. 97 * @lpf: Digital low pass filter frequency. 98 * @accl_fs: accel full scale range. 99 * @accl_en: accel engine enabled 100 * @gyro_en: gyro engine enabled 101 * @temp_en: temperature sensor enabled 102 * @magn_en: magn engine (i2c master) enabled 103 * @accl_fifo_enable: enable accel data output 104 * @gyro_fifo_enable: enable gyro data output 105 * @temp_fifo_enable: enable temp data output 106 * @magn_fifo_enable: enable magn data output 107 * @divider: chip sample rate divider (sample rate divider - 1) 108 */ 109 struct inv_mpu6050_chip_config { 110 unsigned int clk:3; 111 unsigned int fsr:2; 112 unsigned int lpf:3; 113 unsigned int accl_fs:2; 114 unsigned int accl_en:1; 115 unsigned int gyro_en:1; 116 unsigned int temp_en:1; 117 unsigned int magn_en:1; 118 unsigned int accl_fifo_enable:1; 119 unsigned int gyro_fifo_enable:1; 120 unsigned int temp_fifo_enable:1; 121 unsigned int magn_fifo_enable:1; 122 u8 divider; 123 u8 user_ctrl; 124 }; 125 126 /* 127 * Maximum of 6 + 6 + 2 + 7 (for MPU9x50) = 21 round up to 24 and plus 8. 128 * May be less if fewer channels are enabled, as long as the timestamp 129 * remains 8 byte aligned 130 */ 131 #define INV_MPU6050_OUTPUT_DATA_SIZE 32 132 133 /** 134 * struct inv_mpu6050_hw - Other important hardware information. 135 * @whoami: Self identification byte from WHO_AM_I register 136 * @name: name of the chip. 137 * @reg: register map of the chip. 138 * @config: configuration of the chip. 139 * @fifo_size: size of the FIFO in bytes. 140 * @temp: offset and scale to apply to raw temperature. 141 */ 142 struct inv_mpu6050_hw { 143 u8 whoami; 144 u8 *name; 145 const struct inv_mpu6050_reg_map *reg; 146 const struct inv_mpu6050_chip_config *config; 147 size_t fifo_size; 148 struct { 149 int offset; 150 int scale; 151 } temp; 152 }; 153 154 /* 155 * struct inv_mpu6050_state - Driver state variables. 156 * @lock: Chip access lock. 157 * @trig: IIO trigger. 158 * @chip_config: Cached attribute information. 159 * @reg: Map of important registers. 160 * @hw: Other hardware-specific information. 161 * @chip_type: chip type. 162 * @plat_data: platform data (deprecated in favor of @orientation). 163 * @orientation: sensor chip orientation relative to main hardware. 164 * @map regmap pointer. 165 * @irq interrupt number. 166 * @irq_mask the int_pin_cfg mask to configure interrupt type. 167 * @chip_period: chip internal period estimation (~1kHz). 168 * @it_timestamp: timestamp from previous interrupt. 169 * @data_timestamp: timestamp for next data sample. 170 * @vdd_supply: VDD voltage regulator for the chip. 171 * @vddio_supply I/O voltage regulator for the chip. 172 * @magn_disabled: magnetometer disabled for backward compatibility reason. 173 * @magn_raw_to_gauss: coefficient to convert mag raw value to Gauss. 174 * @magn_orient: magnetometer sensor chip orientation if available. 175 * @suspended_sensors: sensors mask of sensors turned off for suspend 176 * @data: dma safe buffer used for bulk reads. 177 */ 178 struct inv_mpu6050_state { 179 struct mutex lock; 180 struct iio_trigger *trig; 181 struct inv_mpu6050_chip_config chip_config; 182 const struct inv_mpu6050_reg_map *reg; 183 const struct inv_mpu6050_hw *hw; 184 enum inv_devices chip_type; 185 struct i2c_mux_core *muxc; 186 struct i2c_client *mux_client; 187 struct inv_mpu6050_platform_data plat_data; 188 struct iio_mount_matrix orientation; 189 struct regmap *map; 190 int irq; 191 u8 irq_mask; 192 unsigned skip_samples; 193 s64 chip_period; 194 s64 it_timestamp; 195 s64 data_timestamp; 196 struct regulator *vdd_supply; 197 struct regulator *vddio_supply; 198 bool magn_disabled; 199 s32 magn_raw_to_gauss[3]; 200 struct iio_mount_matrix magn_orient; 201 unsigned int suspended_sensors; 202 u8 data[INV_MPU6050_OUTPUT_DATA_SIZE] ____cacheline_aligned; 203 }; 204 205 /*register and associated bit definition*/ 206 #define INV_MPU6050_REG_ACCEL_OFFSET 0x06 207 #define INV_MPU6050_REG_GYRO_OFFSET 0x13 208 209 #define INV_MPU6050_REG_SAMPLE_RATE_DIV 0x19 210 #define INV_MPU6050_REG_CONFIG 0x1A 211 #define INV_MPU6050_REG_GYRO_CONFIG 0x1B 212 #define INV_MPU6050_REG_ACCEL_CONFIG 0x1C 213 214 #define INV_MPU6050_REG_FIFO_EN 0x23 215 #define INV_MPU6050_BIT_SLAVE_0 0x01 216 #define INV_MPU6050_BIT_SLAVE_1 0x02 217 #define INV_MPU6050_BIT_SLAVE_2 0x04 218 #define INV_MPU6050_BIT_ACCEL_OUT 0x08 219 #define INV_MPU6050_BITS_GYRO_OUT 0x70 220 #define INV_MPU6050_BIT_TEMP_OUT 0x80 221 222 #define INV_MPU6050_REG_I2C_MST_CTRL 0x24 223 #define INV_MPU6050_BITS_I2C_MST_CLK_400KHZ 0x0D 224 #define INV_MPU6050_BIT_I2C_MST_P_NSR 0x10 225 #define INV_MPU6050_BIT_SLV3_FIFO_EN 0x20 226 #define INV_MPU6050_BIT_WAIT_FOR_ES 0x40 227 #define INV_MPU6050_BIT_MULT_MST_EN 0x80 228 229 /* control I2C slaves from 0 to 3 */ 230 #define INV_MPU6050_REG_I2C_SLV_ADDR(_x) (0x25 + 3 * (_x)) 231 #define INV_MPU6050_BIT_I2C_SLV_RNW 0x80 232 233 #define INV_MPU6050_REG_I2C_SLV_REG(_x) (0x26 + 3 * (_x)) 234 235 #define INV_MPU6050_REG_I2C_SLV_CTRL(_x) (0x27 + 3 * (_x)) 236 #define INV_MPU6050_BIT_SLV_GRP 0x10 237 #define INV_MPU6050_BIT_SLV_REG_DIS 0x20 238 #define INV_MPU6050_BIT_SLV_BYTE_SW 0x40 239 #define INV_MPU6050_BIT_SLV_EN 0x80 240 241 /* I2C master delay register */ 242 #define INV_MPU6050_REG_I2C_SLV4_CTRL 0x34 243 #define INV_MPU6050_BITS_I2C_MST_DLY(_x) ((_x) & 0x1F) 244 245 #define INV_MPU6050_REG_I2C_MST_STATUS 0x36 246 #define INV_MPU6050_BIT_I2C_SLV0_NACK 0x01 247 #define INV_MPU6050_BIT_I2C_SLV1_NACK 0x02 248 #define INV_MPU6050_BIT_I2C_SLV2_NACK 0x04 249 #define INV_MPU6050_BIT_I2C_SLV3_NACK 0x08 250 251 #define INV_MPU6050_REG_INT_ENABLE 0x38 252 #define INV_MPU6050_BIT_DATA_RDY_EN 0x01 253 #define INV_MPU6050_BIT_DMP_INT_EN 0x02 254 255 #define INV_MPU6050_REG_RAW_ACCEL 0x3B 256 #define INV_MPU6050_REG_TEMPERATURE 0x41 257 #define INV_MPU6050_REG_RAW_GYRO 0x43 258 259 #define INV_MPU6050_REG_INT_STATUS 0x3A 260 #define INV_MPU6050_BIT_FIFO_OVERFLOW_INT 0x10 261 #define INV_MPU6050_BIT_RAW_DATA_RDY_INT 0x01 262 263 #define INV_MPU6050_REG_EXT_SENS_DATA 0x49 264 265 /* I2C slaves data output from 0 to 3 */ 266 #define INV_MPU6050_REG_I2C_SLV_DO(_x) (0x63 + (_x)) 267 268 #define INV_MPU6050_REG_I2C_MST_DELAY_CTRL 0x67 269 #define INV_MPU6050_BIT_I2C_SLV0_DLY_EN 0x01 270 #define INV_MPU6050_BIT_I2C_SLV1_DLY_EN 0x02 271 #define INV_MPU6050_BIT_I2C_SLV2_DLY_EN 0x04 272 #define INV_MPU6050_BIT_I2C_SLV3_DLY_EN 0x08 273 #define INV_MPU6050_BIT_DELAY_ES_SHADOW 0x80 274 275 #define INV_MPU6050_REG_SIGNAL_PATH_RESET 0x68 276 #define INV_MPU6050_BIT_TEMP_RST BIT(0) 277 #define INV_MPU6050_BIT_ACCEL_RST BIT(1) 278 #define INV_MPU6050_BIT_GYRO_RST BIT(2) 279 280 #define INV_MPU6050_REG_USER_CTRL 0x6A 281 #define INV_MPU6050_BIT_SIG_COND_RST 0x01 282 #define INV_MPU6050_BIT_FIFO_RST 0x04 283 #define INV_MPU6050_BIT_DMP_RST 0x08 284 #define INV_MPU6050_BIT_I2C_MST_EN 0x20 285 #define INV_MPU6050_BIT_FIFO_EN 0x40 286 #define INV_MPU6050_BIT_DMP_EN 0x80 287 #define INV_MPU6050_BIT_I2C_IF_DIS 0x10 288 289 #define INV_MPU6050_REG_PWR_MGMT_1 0x6B 290 #define INV_MPU6050_BIT_H_RESET 0x80 291 #define INV_MPU6050_BIT_SLEEP 0x40 292 #define INV_MPU6050_BIT_TEMP_DIS 0x08 293 #define INV_MPU6050_BIT_CLK_MASK 0x7 294 295 #define INV_MPU6050_REG_PWR_MGMT_2 0x6C 296 #define INV_MPU6050_BIT_PWR_ACCL_STBY 0x38 297 #define INV_MPU6050_BIT_PWR_GYRO_STBY 0x07 298 299 /* ICM20602 register */ 300 #define INV_ICM20602_REG_I2C_IF 0x70 301 #define INV_ICM20602_BIT_I2C_IF_DIS 0x40 302 303 #define INV_MPU6050_REG_FIFO_COUNT_H 0x72 304 #define INV_MPU6050_REG_FIFO_R_W 0x74 305 306 #define INV_MPU6050_BYTES_PER_3AXIS_SENSOR 6 307 #define INV_MPU6050_FIFO_COUNT_BYTE 2 308 309 /* MPU9X50 9-axis magnetometer */ 310 #define INV_MPU9X50_BYTES_MAGN 7 311 312 /* FIFO temperature sample size */ 313 #define INV_MPU6050_BYTES_PER_TEMP_SENSOR 2 314 315 /* mpu6500 registers */ 316 #define INV_MPU6500_REG_ACCEL_CONFIG_2 0x1D 317 #define INV_ICM20689_BITS_FIFO_SIZE_MAX 0xC0 318 #define INV_MPU6500_REG_ACCEL_OFFSET 0x77 319 320 /* delay time in milliseconds */ 321 #define INV_MPU6050_POWER_UP_TIME 100 322 #define INV_MPU6050_TEMP_UP_TIME 100 323 #define INV_MPU6050_ACCEL_UP_TIME 20 324 #define INV_MPU6050_GYRO_UP_TIME 35 325 #define INV_MPU6050_GYRO_DOWN_TIME 150 326 #define INV_MPU6050_SUSPEND_DELAY_MS 2000 327 328 /* delay time in microseconds */ 329 #define INV_MPU6050_REG_UP_TIME_MIN 5000 330 #define INV_MPU6050_REG_UP_TIME_MAX 10000 331 332 #define INV_MPU6050_TEMP_OFFSET 12420 333 #define INV_MPU6050_TEMP_SCALE 2941176 334 #define INV_MPU6050_MAX_GYRO_FS_PARAM 3 335 #define INV_MPU6050_MAX_ACCL_FS_PARAM 3 336 #define INV_MPU6050_THREE_AXIS 3 337 #define INV_MPU6050_GYRO_CONFIG_FSR_SHIFT 3 338 #define INV_ICM20690_GYRO_CONFIG_FSR_SHIFT 2 339 #define INV_MPU6050_ACCL_CONFIG_FSR_SHIFT 3 340 341 #define INV_MPU6500_TEMP_OFFSET 7011 342 #define INV_MPU6500_TEMP_SCALE 2995178 343 344 #define INV_ICM20608_TEMP_OFFSET 8170 345 #define INV_ICM20608_TEMP_SCALE 3059976 346 347 #define INV_MPU6050_REG_INT_PIN_CFG 0x37 348 #define INV_MPU6050_ACTIVE_HIGH 0x00 349 #define INV_MPU6050_ACTIVE_LOW 0x80 350 /* enable level triggering */ 351 #define INV_MPU6050_LATCH_INT_EN 0x20 352 #define INV_MPU6050_BIT_BYPASS_EN 0x2 353 354 /* Allowed timestamp period jitter in percent */ 355 #define INV_MPU6050_TS_PERIOD_JITTER 4 356 357 /* init parameters */ 358 #define INV_MPU6050_MAX_FIFO_RATE 1000 359 #define INV_MPU6050_MIN_FIFO_RATE 4 360 361 /* chip internal frequency: 1KHz */ 362 #define INV_MPU6050_INTERNAL_FREQ_HZ 1000 363 /* return the frequency divider (chip sample rate divider + 1) */ 364 #define INV_MPU6050_FREQ_DIVIDER(st) \ 365 ((st)->chip_config.divider + 1) 366 /* chip sample rate divider to fifo rate */ 367 #define INV_MPU6050_FIFO_RATE_TO_DIVIDER(fifo_rate) \ 368 ((INV_MPU6050_INTERNAL_FREQ_HZ / (fifo_rate)) - 1) 369 #define INV_MPU6050_DIVIDER_TO_FIFO_RATE(divider) \ 370 (INV_MPU6050_INTERNAL_FREQ_HZ / ((divider) + 1)) 371 372 #define INV_MPU6050_REG_WHOAMI 117 373 374 #define INV_MPU6000_WHOAMI_VALUE 0x68 375 #define INV_MPU6050_WHOAMI_VALUE 0x68 376 #define INV_MPU6500_WHOAMI_VALUE 0x70 377 #define INV_MPU6880_WHOAMI_VALUE 0x78 378 #define INV_MPU9150_WHOAMI_VALUE 0x68 379 #define INV_MPU9250_WHOAMI_VALUE 0x71 380 #define INV_MPU9255_WHOAMI_VALUE 0x73 381 #define INV_MPU6515_WHOAMI_VALUE 0x74 382 #define INV_ICM20608_WHOAMI_VALUE 0xAF 383 #define INV_ICM20609_WHOAMI_VALUE 0xA6 384 #define INV_ICM20689_WHOAMI_VALUE 0x98 385 #define INV_ICM20602_WHOAMI_VALUE 0x12 386 #define INV_ICM20690_WHOAMI_VALUE 0x20 387 #define INV_IAM20680_WHOAMI_VALUE 0xA9 388 389 /* scan element definition for generic MPU6xxx devices */ 390 enum inv_mpu6050_scan { 391 INV_MPU6050_SCAN_ACCL_X, 392 INV_MPU6050_SCAN_ACCL_Y, 393 INV_MPU6050_SCAN_ACCL_Z, 394 INV_MPU6050_SCAN_TEMP, 395 INV_MPU6050_SCAN_GYRO_X, 396 INV_MPU6050_SCAN_GYRO_Y, 397 INV_MPU6050_SCAN_GYRO_Z, 398 INV_MPU6050_SCAN_TIMESTAMP, 399 400 INV_MPU9X50_SCAN_MAGN_X = INV_MPU6050_SCAN_GYRO_Z + 1, 401 INV_MPU9X50_SCAN_MAGN_Y, 402 INV_MPU9X50_SCAN_MAGN_Z, 403 INV_MPU9X50_SCAN_TIMESTAMP, 404 }; 405 406 enum inv_mpu6050_filter_e { 407 INV_MPU6050_FILTER_NOLPF2 = 0, 408 INV_MPU6050_FILTER_200HZ, 409 INV_MPU6050_FILTER_100HZ, 410 INV_MPU6050_FILTER_45HZ, 411 INV_MPU6050_FILTER_20HZ, 412 INV_MPU6050_FILTER_10HZ, 413 INV_MPU6050_FILTER_5HZ, 414 INV_MPU6050_FILTER_NOLPF, 415 NUM_MPU6050_FILTER 416 }; 417 418 /* IIO attribute address */ 419 enum INV_MPU6050_IIO_ATTR_ADDR { 420 ATTR_GYRO_MATRIX, 421 ATTR_ACCL_MATRIX, 422 }; 423 424 enum inv_mpu6050_accl_fs_e { 425 INV_MPU6050_FS_02G = 0, 426 INV_MPU6050_FS_04G, 427 INV_MPU6050_FS_08G, 428 INV_MPU6050_FS_16G, 429 NUM_ACCL_FSR 430 }; 431 432 enum inv_mpu6050_fsr_e { 433 INV_MPU6050_FSR_250DPS = 0, 434 INV_MPU6050_FSR_500DPS, 435 INV_MPU6050_FSR_1000DPS, 436 INV_MPU6050_FSR_2000DPS, 437 NUM_MPU6050_FSR 438 }; 439 440 enum inv_mpu6050_clock_sel_e { 441 INV_CLK_INTERNAL = 0, 442 INV_CLK_PLL, 443 NUM_CLK 444 }; 445 446 irqreturn_t inv_mpu6050_read_fifo(int irq, void *p); 447 int inv_mpu6050_probe_trigger(struct iio_dev *indio_dev, int irq_type); 448 int inv_mpu6050_prepare_fifo(struct inv_mpu6050_state *st, bool enable); 449 int inv_mpu6050_switch_engine(struct inv_mpu6050_state *st, bool en, 450 unsigned int mask); 451 int inv_mpu6050_write_reg(struct inv_mpu6050_state *st, int reg, u8 val); 452 int inv_mpu_acpi_create_mux_client(struct i2c_client *client); 453 void inv_mpu_acpi_delete_mux_client(struct i2c_client *client); 454 int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name, 455 int (*inv_mpu_bus_setup)(struct iio_dev *), int chip_type); 456 extern const struct dev_pm_ops inv_mpu_pmops; 457 458 #endif 459