1 /* 2 * Copyright (c) 2009, Intel Corporation. 3 * 4 * This program is free software; you can redistribute it and/or modify it 5 * under the terms and conditions of the GNU General Public License, 6 * version 2, as published by the Free Software Foundation. 7 * 8 * This program is distributed in the hope it will be useful, but WITHOUT 9 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 10 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for 11 * more details. 12 * 13 * You should have received a copy of the GNU General Public License along with 14 * this program; if not, write to the Free Software Foundation, Inc., 15 * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. 16 */ 17 #ifndef __PSB_INTEL_REG_H__ 18 #define __PSB_INTEL_REG_H__ 19 20 /* 21 * GPIO regs 22 */ 23 #define GPIOA 0x5010 24 #define GPIOB 0x5014 25 #define GPIOC 0x5018 26 #define GPIOD 0x501c 27 #define GPIOE 0x5020 28 #define GPIOF 0x5024 29 #define GPIOG 0x5028 30 #define GPIOH 0x502c 31 # define GPIO_CLOCK_DIR_MASK (1 << 0) 32 # define GPIO_CLOCK_DIR_IN (0 << 1) 33 # define GPIO_CLOCK_DIR_OUT (1 << 1) 34 # define GPIO_CLOCK_VAL_MASK (1 << 2) 35 # define GPIO_CLOCK_VAL_OUT (1 << 3) 36 # define GPIO_CLOCK_VAL_IN (1 << 4) 37 # define GPIO_CLOCK_PULLUP_DISABLE (1 << 5) 38 # define GPIO_DATA_DIR_MASK (1 << 8) 39 # define GPIO_DATA_DIR_IN (0 << 9) 40 # define GPIO_DATA_DIR_OUT (1 << 9) 41 # define GPIO_DATA_VAL_MASK (1 << 10) 42 # define GPIO_DATA_VAL_OUT (1 << 11) 43 # define GPIO_DATA_VAL_IN (1 << 12) 44 # define GPIO_DATA_PULLUP_DISABLE (1 << 13) 45 46 #define GMBUS0 0x5100 /* clock/port select */ 47 #define GMBUS_RATE_100KHZ (0<<8) 48 #define GMBUS_RATE_50KHZ (1<<8) 49 #define GMBUS_RATE_400KHZ (2<<8) /* reserved on Pineview */ 50 #define GMBUS_RATE_1MHZ (3<<8) /* reserved on Pineview */ 51 #define GMBUS_HOLD_EXT (1<<7) /* 300ns hold time, rsvd on Pineview */ 52 #define GMBUS_PORT_DISABLED 0 53 #define GMBUS_PORT_SSC 1 54 #define GMBUS_PORT_VGADDC 2 55 #define GMBUS_PORT_PANEL 3 56 #define GMBUS_PORT_DPC 4 /* HDMIC */ 57 #define GMBUS_PORT_DPB 5 /* SDVO, HDMIB */ 58 /* 6 reserved */ 59 #define GMBUS_PORT_DPD 7 /* HDMID */ 60 #define GMBUS_NUM_PORTS 8 61 #define GMBUS1 0x5104 /* command/status */ 62 #define GMBUS_SW_CLR_INT (1<<31) 63 #define GMBUS_SW_RDY (1<<30) 64 #define GMBUS_ENT (1<<29) /* enable timeout */ 65 #define GMBUS_CYCLE_NONE (0<<25) 66 #define GMBUS_CYCLE_WAIT (1<<25) 67 #define GMBUS_CYCLE_INDEX (2<<25) 68 #define GMBUS_CYCLE_STOP (4<<25) 69 #define GMBUS_BYTE_COUNT_SHIFT 16 70 #define GMBUS_SLAVE_INDEX_SHIFT 8 71 #define GMBUS_SLAVE_ADDR_SHIFT 1 72 #define GMBUS_SLAVE_READ (1<<0) 73 #define GMBUS_SLAVE_WRITE (0<<0) 74 #define GMBUS2 0x5108 /* status */ 75 #define GMBUS_INUSE (1<<15) 76 #define GMBUS_HW_WAIT_PHASE (1<<14) 77 #define GMBUS_STALL_TIMEOUT (1<<13) 78 #define GMBUS_INT (1<<12) 79 #define GMBUS_HW_RDY (1<<11) 80 #define GMBUS_SATOER (1<<10) 81 #define GMBUS_ACTIVE (1<<9) 82 #define GMBUS3 0x510c /* data buffer bytes 3-0 */ 83 #define GMBUS4 0x5110 /* interrupt mask (Pineview+) */ 84 #define GMBUS_SLAVE_TIMEOUT_EN (1<<4) 85 #define GMBUS_NAK_EN (1<<3) 86 #define GMBUS_IDLE_EN (1<<2) 87 #define GMBUS_HW_WAIT_EN (1<<1) 88 #define GMBUS_HW_RDY_EN (1<<0) 89 #define GMBUS5 0x5120 /* byte index */ 90 #define GMBUS_2BYTE_INDEX_EN (1<<31) 91 92 #define BLC_PWM_CTL 0x61254 93 #define BLC_PWM_CTL2 0x61250 94 #define PWM_ENABLE (1 << 31) 95 #define PWM_LEGACY_MODE (1 << 30) 96 #define PWM_PIPE_B (1 << 29) 97 #define BLC_PWM_CTL_C 0x62254 98 #define BLC_PWM_CTL2_C 0x62250 99 #define BACKLIGHT_MODULATION_FREQ_SHIFT (17) 100 /* 101 * This is the most significant 15 bits of the number of backlight cycles in a 102 * complete cycle of the modulated backlight control. 103 * 104 * The actual value is this field multiplied by two. 105 */ 106 #define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17) 107 #define BLM_LEGACY_MODE (1 << 16) 108 /* 109 * This is the number of cycles out of the backlight modulation cycle for which 110 * the backlight is on. 111 * 112 * This field must be no greater than the number of cycles in the complete 113 * backlight modulation cycle. 114 */ 115 #define BACKLIGHT_DUTY_CYCLE_SHIFT (0) 116 #define BACKLIGHT_DUTY_CYCLE_MASK (0xffff) 117 118 #define I915_GCFGC 0xf0 119 #define I915_LOW_FREQUENCY_ENABLE (1 << 7) 120 #define I915_DISPLAY_CLOCK_190_200_MHZ (0 << 4) 121 #define I915_DISPLAY_CLOCK_333_MHZ (4 << 4) 122 #define I915_DISPLAY_CLOCK_MASK (7 << 4) 123 124 #define I855_HPLLCC 0xc0 125 #define I855_CLOCK_CONTROL_MASK (3 << 0) 126 #define I855_CLOCK_133_200 (0 << 0) 127 #define I855_CLOCK_100_200 (1 << 0) 128 #define I855_CLOCK_100_133 (2 << 0) 129 #define I855_CLOCK_166_250 (3 << 0) 130 131 /* I830 CRTC registers */ 132 #define HTOTAL_A 0x60000 133 #define HBLANK_A 0x60004 134 #define HSYNC_A 0x60008 135 #define VTOTAL_A 0x6000c 136 #define VBLANK_A 0x60010 137 #define VSYNC_A 0x60014 138 #define PIPEASRC 0x6001c 139 #define BCLRPAT_A 0x60020 140 #define VSYNCSHIFT_A 0x60028 141 142 #define HTOTAL_B 0x61000 143 #define HBLANK_B 0x61004 144 #define HSYNC_B 0x61008 145 #define VTOTAL_B 0x6100c 146 #define VBLANK_B 0x61010 147 #define VSYNC_B 0x61014 148 #define PIPEBSRC 0x6101c 149 #define BCLRPAT_B 0x61020 150 #define VSYNCSHIFT_B 0x61028 151 152 #define HTOTAL_C 0x62000 153 #define HBLANK_C 0x62004 154 #define HSYNC_C 0x62008 155 #define VTOTAL_C 0x6200c 156 #define VBLANK_C 0x62010 157 #define VSYNC_C 0x62014 158 #define PIPECSRC 0x6201c 159 #define BCLRPAT_C 0x62020 160 #define VSYNCSHIFT_C 0x62028 161 162 #define PP_STATUS 0x61200 163 # define PP_ON (1 << 31) 164 /* 165 * Indicates that all dependencies of the panel are on: 166 * 167 * - PLL enabled 168 * - pipe enabled 169 * - LVDS/DVOB/DVOC on 170 */ 171 #define PP_READY (1 << 30) 172 #define PP_SEQUENCE_NONE (0 << 28) 173 #define PP_SEQUENCE_ON (1 << 28) 174 #define PP_SEQUENCE_OFF (2 << 28) 175 #define PP_SEQUENCE_MASK 0x30000000 176 #define PP_CYCLE_DELAY_ACTIVE (1 << 27) 177 #define PP_SEQUENCE_STATE_ON_IDLE (1 << 3) 178 #define PP_SEQUENCE_STATE_MASK 0x0000000f 179 180 #define PP_CONTROL 0x61204 181 #define POWER_TARGET_ON (1 << 0) 182 #define PANEL_UNLOCK_REGS (0xabcd << 16) 183 #define PANEL_UNLOCK_MASK (0xffff << 16) 184 #define EDP_FORCE_VDD (1 << 3) 185 #define EDP_BLC_ENABLE (1 << 2) 186 #define PANEL_POWER_RESET (1 << 1) 187 #define PANEL_POWER_OFF (0 << 0) 188 #define PANEL_POWER_ON (1 << 0) 189 190 /* Poulsbo/Oaktrail */ 191 #define LVDSPP_ON 0x61208 192 #define LVDSPP_OFF 0x6120c 193 #define PP_CYCLE 0x61210 194 195 /* Cedartrail */ 196 #define PP_ON_DELAYS 0x61208 /* Cedartrail */ 197 #define PANEL_PORT_SELECT_MASK (3 << 30) 198 #define PANEL_PORT_SELECT_LVDS (0 << 30) 199 #define PANEL_PORT_SELECT_EDP (1 << 30) 200 #define PANEL_POWER_UP_DELAY_MASK (0x1fff0000) 201 #define PANEL_POWER_UP_DELAY_SHIFT 16 202 #define PANEL_LIGHT_ON_DELAY_MASK (0x1fff) 203 #define PANEL_LIGHT_ON_DELAY_SHIFT 0 204 205 #define PP_OFF_DELAYS 0x6120c /* Cedartrail */ 206 #define PANEL_POWER_DOWN_DELAY_MASK (0x1fff0000) 207 #define PANEL_POWER_DOWN_DELAY_SHIFT 16 208 #define PANEL_LIGHT_OFF_DELAY_MASK (0x1fff) 209 #define PANEL_LIGHT_OFF_DELAY_SHIFT 0 210 211 #define PP_DIVISOR 0x61210 /* Cedartrail */ 212 #define PP_REFERENCE_DIVIDER_MASK (0xffffff00) 213 #define PP_REFERENCE_DIVIDER_SHIFT 8 214 #define PANEL_POWER_CYCLE_DELAY_MASK (0x1f) 215 #define PANEL_POWER_CYCLE_DELAY_SHIFT 0 216 217 #define PFIT_CONTROL 0x61230 218 #define PFIT_ENABLE (1 << 31) 219 #define PFIT_PIPE_MASK (3 << 29) 220 #define PFIT_PIPE_SHIFT 29 221 #define PFIT_SCALING_MODE_PILLARBOX (1 << 27) 222 #define PFIT_SCALING_MODE_LETTERBOX (3 << 26) 223 #define VERT_INTERP_DISABLE (0 << 10) 224 #define VERT_INTERP_BILINEAR (1 << 10) 225 #define VERT_INTERP_MASK (3 << 10) 226 #define VERT_AUTO_SCALE (1 << 9) 227 #define HORIZ_INTERP_DISABLE (0 << 6) 228 #define HORIZ_INTERP_BILINEAR (1 << 6) 229 #define HORIZ_INTERP_MASK (3 << 6) 230 #define HORIZ_AUTO_SCALE (1 << 5) 231 #define PANEL_8TO6_DITHER_ENABLE (1 << 3) 232 233 #define PFIT_PGM_RATIOS 0x61234 234 #define PFIT_VERT_SCALE_MASK 0xfff00000 235 #define PFIT_HORIZ_SCALE_MASK 0x0000fff0 236 237 #define PFIT_AUTO_RATIOS 0x61238 238 239 #define DPLL_A 0x06014 240 #define DPLL_B 0x06018 241 #define DPLL_VCO_ENABLE (1 << 31) 242 #define DPLL_DVO_HIGH_SPEED (1 << 30) 243 #define DPLL_SYNCLOCK_ENABLE (1 << 29) 244 #define DPLL_VGA_MODE_DIS (1 << 28) 245 #define DPLLB_MODE_DAC_SERIAL (1 << 26) /* i915 */ 246 #define DPLLB_MODE_LVDS (2 << 26) /* i915 */ 247 #define DPLL_MODE_MASK (3 << 26) 248 #define DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 (0 << 24) /* i915 */ 249 #define DPLL_DAC_SERIAL_P2_CLOCK_DIV_5 (1 << 24) /* i915 */ 250 #define DPLLB_LVDS_P2_CLOCK_DIV_14 (0 << 24) /* i915 */ 251 #define DPLLB_LVDS_P2_CLOCK_DIV_7 (1 << 24) /* i915 */ 252 #define DPLL_P2_CLOCK_DIV_MASK 0x03000000 /* i915 */ 253 #define DPLL_FPA0h1_P1_POST_DIV_MASK 0x00ff0000 /* i915 */ 254 #define DPLL_LOCK (1 << 15) /* CDV */ 255 256 /* 257 * The i830 generation, in DAC/serial mode, defines p1 as two plus this 258 * bitfield, or just 2 if PLL_P1_DIVIDE_BY_TWO is set. 259 */ 260 # define DPLL_FPA01_P1_POST_DIV_MASK_I830 0x001f0000 261 /* 262 * The i830 generation, in LVDS mode, defines P1 as the bit number set within 263 * this field (only one bit may be set). 264 */ 265 #define DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS 0x003f0000 266 #define DPLL_FPA01_P1_POST_DIV_SHIFT 16 267 #define PLL_P2_DIVIDE_BY_4 (1 << 23) /* i830, required 268 * in DVO non-gang */ 269 # define PLL_P1_DIVIDE_BY_TWO (1 << 21) /* i830 */ 270 #define PLL_REF_INPUT_DREFCLK (0 << 13) 271 #define PLL_REF_INPUT_TVCLKINA (1 << 13) /* i830 */ 272 #define PLL_REF_INPUT_TVCLKINBC (2 << 13) /* SDVO 273 * TVCLKIN */ 274 #define PLLB_REF_INPUT_SPREADSPECTRUMIN (3 << 13) 275 #define PLL_REF_INPUT_MASK (3 << 13) 276 #define PLL_LOAD_PULSE_PHASE_SHIFT 9 277 /* 278 * Parallel to Serial Load Pulse phase selection. 279 * Selects the phase for the 10X DPLL clock for the PCIe 280 * digital display port. The range is 4 to 13; 10 or more 281 * is just a flip delay. The default is 6 282 */ 283 #define PLL_LOAD_PULSE_PHASE_MASK (0xf << PLL_LOAD_PULSE_PHASE_SHIFT) 284 #define DISPLAY_RATE_SELECT_FPA1 (1 << 8) 285 286 /* 287 * SDVO multiplier for 945G/GM. Not used on 965. 288 * 289 * DPLL_MD_UDI_MULTIPLIER_MASK 290 */ 291 #define SDVO_MULTIPLIER_MASK 0x000000ff 292 #define SDVO_MULTIPLIER_SHIFT_HIRES 4 293 #define SDVO_MULTIPLIER_SHIFT_VGA 0 294 295 /* 296 * PLL_MD 297 */ 298 /* Pipe A SDVO/UDI clock multiplier/divider register for G965. */ 299 #define DPLL_A_MD 0x0601c 300 /* Pipe B SDVO/UDI clock multiplier/divider register for G965. */ 301 #define DPLL_B_MD 0x06020 302 /* 303 * UDI pixel divider, controlling how many pixels are stuffed into a packet. 304 * 305 * Value is pixels minus 1. Must be set to 1 pixel for SDVO. 306 */ 307 #define DPLL_MD_UDI_DIVIDER_MASK 0x3f000000 308 #define DPLL_MD_UDI_DIVIDER_SHIFT 24 309 /* UDI pixel divider for VGA, same as DPLL_MD_UDI_DIVIDER_MASK. */ 310 #define DPLL_MD_VGA_UDI_DIVIDER_MASK 0x003f0000 311 #define DPLL_MD_VGA_UDI_DIVIDER_SHIFT 16 312 /* 313 * SDVO/UDI pixel multiplier. 314 * 315 * SDVO requires that the bus clock rate be between 1 and 2 Ghz, and the bus 316 * clock rate is 10 times the DPLL clock. At low resolution/refresh rate 317 * modes, the bus rate would be below the limits, so SDVO allows for stuffing 318 * dummy bytes in the datastream at an increased clock rate, with both sides of 319 * the link knowing how many bytes are fill. 320 * 321 * So, for a mode with a dotclock of 65Mhz, we would want to double the clock 322 * rate to 130Mhz to get a bus rate of 1.30Ghz. The DPLL clock rate would be 323 * set to 130Mhz, and the SDVO multiplier set to 2x in this register and 324 * through an SDVO command. 325 * 326 * This register field has values of multiplication factor minus 1, with 327 * a maximum multiplier of 5 for SDVO. 328 */ 329 #define DPLL_MD_UDI_MULTIPLIER_MASK 0x00003f00 330 #define DPLL_MD_UDI_MULTIPLIER_SHIFT 8 331 /* 332 * SDVO/UDI pixel multiplier for VGA, same as DPLL_MD_UDI_MULTIPLIER_MASK. 333 * This best be set to the default value (3) or the CRT won't work. No, 334 * I don't entirely understand what this does... 335 */ 336 #define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f 337 #define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0 338 339 #define DPLL_TEST 0x606c 340 #define DPLLB_TEST_SDVO_DIV_1 (0 << 22) 341 #define DPLLB_TEST_SDVO_DIV_2 (1 << 22) 342 #define DPLLB_TEST_SDVO_DIV_4 (2 << 22) 343 #define DPLLB_TEST_SDVO_DIV_MASK (3 << 22) 344 #define DPLLB_TEST_N_BYPASS (1 << 19) 345 #define DPLLB_TEST_M_BYPASS (1 << 18) 346 #define DPLLB_INPUT_BUFFER_ENABLE (1 << 16) 347 #define DPLLA_TEST_N_BYPASS (1 << 3) 348 #define DPLLA_TEST_M_BYPASS (1 << 2) 349 #define DPLLA_INPUT_BUFFER_ENABLE (1 << 0) 350 351 #define ADPA 0x61100 352 #define ADPA_DAC_ENABLE (1 << 31) 353 #define ADPA_DAC_DISABLE 0 354 #define ADPA_PIPE_SELECT_MASK (1 << 30) 355 #define ADPA_PIPE_A_SELECT 0 356 #define ADPA_PIPE_B_SELECT (1 << 30) 357 #define ADPA_USE_VGA_HVPOLARITY (1 << 15) 358 #define ADPA_SETS_HVPOLARITY 0 359 #define ADPA_VSYNC_CNTL_DISABLE (1 << 11) 360 #define ADPA_VSYNC_CNTL_ENABLE 0 361 #define ADPA_HSYNC_CNTL_DISABLE (1 << 10) 362 #define ADPA_HSYNC_CNTL_ENABLE 0 363 #define ADPA_VSYNC_ACTIVE_HIGH (1 << 4) 364 #define ADPA_VSYNC_ACTIVE_LOW 0 365 #define ADPA_HSYNC_ACTIVE_HIGH (1 << 3) 366 #define ADPA_HSYNC_ACTIVE_LOW 0 367 368 #define FPA0 0x06040 369 #define FPA1 0x06044 370 #define FPB0 0x06048 371 #define FPB1 0x0604c 372 #define FP_N_DIV_MASK 0x003f0000 373 #define FP_N_DIV_SHIFT 16 374 #define FP_M1_DIV_MASK 0x00003f00 375 #define FP_M1_DIV_SHIFT 8 376 #define FP_M2_DIV_MASK 0x0000003f 377 #define FP_M2_DIV_SHIFT 0 378 379 #define PORT_HOTPLUG_EN 0x61110 380 #define HDMIB_HOTPLUG_INT_EN (1 << 29) 381 #define HDMIC_HOTPLUG_INT_EN (1 << 28) 382 #define HDMID_HOTPLUG_INT_EN (1 << 27) 383 #define SDVOB_HOTPLUG_INT_EN (1 << 26) 384 #define SDVOC_HOTPLUG_INT_EN (1 << 25) 385 #define TV_HOTPLUG_INT_EN (1 << 18) 386 #define CRT_HOTPLUG_INT_EN (1 << 9) 387 #define CRT_HOTPLUG_FORCE_DETECT (1 << 3) 388 /* CDV.. */ 389 #define CRT_HOTPLUG_ACTIVATION_PERIOD_64 (1 << 8) 390 #define CRT_HOTPLUG_DAC_ON_TIME_2M (0 << 7) 391 #define CRT_HOTPLUG_DAC_ON_TIME_4M (1 << 7) 392 #define CRT_HOTPLUG_VOLTAGE_COMPARE_40 (0 << 5) 393 #define CRT_HOTPLUG_VOLTAGE_COMPARE_50 (1 << 5) 394 #define CRT_HOTPLUG_VOLTAGE_COMPARE_60 (2 << 5) 395 #define CRT_HOTPLUG_VOLTAGE_COMPARE_70 (3 << 5) 396 #define CRT_HOTPLUG_VOLTAGE_COMPARE_MASK (3 << 5) 397 #define CRT_HOTPLUG_DETECT_DELAY_1G (0 << 4) 398 #define CRT_HOTPLUG_DETECT_DELAY_2G (1 << 4) 399 #define CRT_HOTPLUG_DETECT_VOLTAGE_325MV (0 << 2) 400 #define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2) 401 #define CRT_HOTPLUG_DETECT_MASK 0x000000F8 402 403 #define PORT_HOTPLUG_STAT 0x61114 404 #define CRT_HOTPLUG_INT_STATUS (1 << 11) 405 #define TV_HOTPLUG_INT_STATUS (1 << 10) 406 #define CRT_HOTPLUG_MONITOR_MASK (3 << 8) 407 #define CRT_HOTPLUG_MONITOR_COLOR (3 << 8) 408 #define CRT_HOTPLUG_MONITOR_MONO (2 << 8) 409 #define CRT_HOTPLUG_MONITOR_NONE (0 << 8) 410 #define SDVOC_HOTPLUG_INT_STATUS (1 << 7) 411 #define SDVOB_HOTPLUG_INT_STATUS (1 << 6) 412 413 #define SDVOB 0x61140 414 #define SDVOC 0x61160 415 #define SDVO_ENABLE (1 << 31) 416 #define SDVO_PIPE_B_SELECT (1 << 30) 417 #define SDVO_STALL_SELECT (1 << 29) 418 #define SDVO_INTERRUPT_ENABLE (1 << 26) 419 #define SDVO_COLOR_RANGE_16_235 (1 << 8) 420 #define SDVO_AUDIO_ENABLE (1 << 6) 421 422 /** 423 * 915G/GM SDVO pixel multiplier. 424 * 425 * Programmed value is multiplier - 1, up to 5x. 426 * 427 * DPLL_MD_UDI_MULTIPLIER_MASK 428 */ 429 #define SDVO_PORT_MULTIPLY_MASK (7 << 23) 430 #define SDVO_PORT_MULTIPLY_SHIFT 23 431 #define SDVO_PHASE_SELECT_MASK (15 << 19) 432 #define SDVO_PHASE_SELECT_DEFAULT (6 << 19) 433 #define SDVO_CLOCK_OUTPUT_INVERT (1 << 18) 434 #define SDVOC_GANG_MODE (1 << 16) 435 #define SDVO_BORDER_ENABLE (1 << 7) 436 #define SDVOB_PCIE_CONCURRENCY (1 << 3) 437 #define SDVO_DETECTED (1 << 2) 438 /* Bits to be preserved when writing */ 439 #define SDVOB_PRESERVE_MASK ((1 << 17) | (1 << 16) | (1 << 14)) 440 #define SDVOC_PRESERVE_MASK (1 << 17) 441 442 /* 443 * This register controls the LVDS output enable, pipe selection, and data 444 * format selection. 445 * 446 * All of the clock/data pairs are force powered down by power sequencing. 447 */ 448 #define LVDS 0x61180 449 /* 450 * Enables the LVDS port. This bit must be set before DPLLs are enabled, as 451 * the DPLL semantics change when the LVDS is assigned to that pipe. 452 */ 453 #define LVDS_PORT_EN (1 << 31) 454 /* Selects pipe B for LVDS data. Must be set on pre-965. */ 455 #define LVDS_PIPEB_SELECT (1 << 30) 456 457 /* Turns on border drawing to allow centered display. */ 458 #define LVDS_BORDER_EN (1 << 15) 459 460 /* 461 * Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per 462 * pixel. 463 */ 464 #define LVDS_A0A2_CLKA_POWER_MASK (3 << 8) 465 #define LVDS_A0A2_CLKA_POWER_DOWN (0 << 8) 466 #define LVDS_A0A2_CLKA_POWER_UP (3 << 8) 467 /* 468 * Controls the A3 data pair, which contains the additional LSBs for 24 bit 469 * mode. Only enabled if LVDS_A0A2_CLKA_POWER_UP also indicates it should be 470 * on. 471 */ 472 #define LVDS_A3_POWER_MASK (3 << 6) 473 #define LVDS_A3_POWER_DOWN (0 << 6) 474 #define LVDS_A3_POWER_UP (3 << 6) 475 /* 476 * Controls the CLKB pair. This should only be set when LVDS_B0B3_POWER_UP 477 * is set. 478 */ 479 #define LVDS_CLKB_POWER_MASK (3 << 4) 480 #define LVDS_CLKB_POWER_DOWN (0 << 4) 481 #define LVDS_CLKB_POWER_UP (3 << 4) 482 /* 483 * Controls the B0-B3 data pairs. This must be set to match the DPLL p2 484 * setting for whether we are in dual-channel mode. The B3 pair will 485 * additionally only be powered up when LVDS_A3_POWER_UP is set. 486 */ 487 #define LVDS_B0B3_POWER_MASK (3 << 2) 488 #define LVDS_B0B3_POWER_DOWN (0 << 2) 489 #define LVDS_B0B3_POWER_UP (3 << 2) 490 491 #define PIPEACONF 0x70008 492 #define PIPEACONF_ENABLE (1 << 31) 493 #define PIPEACONF_DISABLE 0 494 #define PIPEACONF_DOUBLE_WIDE (1 << 30) 495 #define PIPECONF_ACTIVE (1 << 30) 496 #define I965_PIPECONF_ACTIVE (1 << 30) 497 #define PIPECONF_DSIPLL_LOCK (1 << 29) 498 #define PIPEACONF_SINGLE_WIDE 0 499 #define PIPEACONF_PIPE_UNLOCKED 0 500 #define PIPEACONF_DSR (1 << 26) 501 #define PIPEACONF_PIPE_LOCKED (1 << 25) 502 #define PIPEACONF_PALETTE 0 503 #define PIPECONF_FORCE_BORDER (1 << 25) 504 #define PIPEACONF_GAMMA (1 << 24) 505 #define PIPECONF_PROGRESSIVE (0 << 21) 506 #define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21) 507 #define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21) 508 #define PIPECONF_PLANE_OFF (1 << 19) 509 #define PIPECONF_CURSOR_OFF (1 << 18) 510 511 #define PIPEBCONF 0x71008 512 #define PIPEBCONF_ENABLE (1 << 31) 513 #define PIPEBCONF_DISABLE 0 514 #define PIPEBCONF_DOUBLE_WIDE (1 << 30) 515 #define PIPEBCONF_DISABLE 0 516 #define PIPEBCONF_GAMMA (1 << 24) 517 #define PIPEBCONF_PALETTE 0 518 519 #define PIPECCONF 0x72008 520 521 #define PIPEBGCMAXRED 0x71010 522 #define PIPEBGCMAXGREEN 0x71014 523 #define PIPEBGCMAXBLUE 0x71018 524 525 #define PIPEASTAT 0x70024 526 #define PIPEBSTAT 0x71024 527 #define PIPECSTAT 0x72024 528 #define PIPE_VBLANK_INTERRUPT_STATUS (1UL << 1) 529 #define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL << 2) 530 #define PIPE_VBLANK_CLEAR (1 << 1) 531 #define PIPE_VBLANK_STATUS (1 << 1) 532 #define PIPE_TE_STATUS (1UL << 6) 533 #define PIPE_DPST_EVENT_STATUS (1UL << 7) 534 #define PIPE_VSYNC_CLEAR (1UL << 9) 535 #define PIPE_VSYNC_STATUS (1UL << 9) 536 #define PIPE_HDMI_AUDIO_UNDERRUN_STATUS (1UL << 10) 537 #define PIPE_HDMI_AUDIO_BUFFER_DONE_STATUS (1UL << 11) 538 #define PIPE_VBLANK_INTERRUPT_ENABLE (1UL << 17) 539 #define PIPE_START_VBLANK_INTERRUPT_ENABLE (1UL << 18) 540 #define PIPE_TE_ENABLE (1UL << 22) 541 #define PIPE_LEGACY_BLC_EVENT_ENABLE (1UL << 22) 542 #define PIPE_DPST_EVENT_ENABLE (1UL << 23) 543 #define PIPE_VSYNC_ENABL (1UL << 25) 544 #define PIPE_HDMI_AUDIO_UNDERRUN (1UL << 26) 545 #define PIPE_HDMI_AUDIO_BUFFER_DONE (1UL << 27) 546 #define PIPE_FIFO_UNDERRUN (1UL << 31) 547 #define PIPE_HDMI_AUDIO_INT_MASK (PIPE_HDMI_AUDIO_UNDERRUN | \ 548 PIPE_HDMI_AUDIO_BUFFER_DONE) 549 #define PIPE_EVENT_MASK ((1 << 29)|(1 << 28)|(1 << 27)|(1 << 26)|(1 << 24)|(1 << 23)|(1 << 22)|(1 << 21)|(1 << 20)|(1 << 16)) 550 #define PIPE_VBLANK_MASK ((1 << 25)|(1 << 24)|(1 << 18)|(1 << 17)) 551 #define HISTOGRAM_INT_CONTROL 0x61268 552 #define HISTOGRAM_BIN_DATA 0X61264 553 #define HISTOGRAM_LOGIC_CONTROL 0x61260 554 #define PWM_CONTROL_LOGIC 0x61250 555 #define PIPE_HOTPLUG_INTERRUPT_STATUS (1UL << 10) 556 #define HISTOGRAM_INTERRUPT_ENABLE (1UL << 31) 557 #define HISTOGRAM_LOGIC_ENABLE (1UL << 31) 558 #define PWM_LOGIC_ENABLE (1UL << 31) 559 #define PWM_PHASEIN_ENABLE (1UL << 25) 560 #define PWM_PHASEIN_INT_ENABLE (1UL << 24) 561 #define PWM_PHASEIN_VB_COUNT 0x00001f00 562 #define PWM_PHASEIN_INC 0x0000001f 563 #define HISTOGRAM_INT_CTRL_CLEAR (1UL << 30) 564 #define DPST_YUV_LUMA_MODE 0 565 566 struct dpst_ie_histogram_control { 567 union { 568 uint32_t data; 569 struct { 570 uint32_t bin_reg_index:7; 571 uint32_t reserved:4; 572 uint32_t bin_reg_func_select:1; 573 uint32_t sync_to_phase_in:1; 574 uint32_t alt_enhancement_mode:2; 575 uint32_t reserved1:1; 576 uint32_t sync_to_phase_in_count:8; 577 uint32_t histogram_mode_select:1; 578 uint32_t reserved2:4; 579 uint32_t ie_pipe_assignment:1; 580 uint32_t ie_mode_table_enabled:1; 581 uint32_t ie_histogram_enable:1; 582 }; 583 }; 584 }; 585 586 struct dpst_guardband { 587 union { 588 uint32_t data; 589 struct { 590 uint32_t guardband:22; 591 uint32_t guardband_interrupt_delay:8; 592 uint32_t interrupt_status:1; 593 uint32_t interrupt_enable:1; 594 }; 595 }; 596 }; 597 598 #define PIPEAFRAMEHIGH 0x70040 599 #define PIPEAFRAMEPIXEL 0x70044 600 #define PIPEBFRAMEHIGH 0x71040 601 #define PIPEBFRAMEPIXEL 0x71044 602 #define PIPECFRAMEHIGH 0x72040 603 #define PIPECFRAMEPIXEL 0x72044 604 #define PIPE_FRAME_HIGH_MASK 0x0000ffff 605 #define PIPE_FRAME_HIGH_SHIFT 0 606 #define PIPE_FRAME_LOW_MASK 0xff000000 607 #define PIPE_FRAME_LOW_SHIFT 24 608 #define PIPE_PIXEL_MASK 0x00ffffff 609 #define PIPE_PIXEL_SHIFT 0 610 611 #define FW_BLC_SELF 0x20e0 612 #define FW_BLC_SELF_EN (1<<15) 613 614 #define DSPARB 0x70030 615 #define DSPFW1 0x70034 616 #define DSP_FIFO_SR_WM_MASK 0xFF800000 617 #define DSP_FIFO_SR_WM_SHIFT 23 618 #define CURSOR_B_FIFO_WM_MASK 0x003F0000 619 #define CURSOR_B_FIFO_WM_SHIFT 16 620 #define DSPFW2 0x70038 621 #define CURSOR_A_FIFO_WM_MASK 0x3F00 622 #define CURSOR_A_FIFO_WM_SHIFT 8 623 #define DSP_PLANE_C_FIFO_WM_MASK 0x7F 624 #define DSP_PLANE_C_FIFO_WM_SHIFT 0 625 #define DSPFW3 0x7003c 626 #define DSPFW4 0x70050 627 #define DSPFW5 0x70054 628 #define DSP_PLANE_B_FIFO_WM1_SHIFT 24 629 #define DSP_PLANE_A_FIFO_WM1_SHIFT 16 630 #define CURSOR_B_FIFO_WM1_SHIFT 8 631 #define CURSOR_FIFO_SR_WM1_SHIFT 0 632 #define DSPFW6 0x70058 633 #define DSPCHICKENBIT 0x70400 634 #define DSPACNTR 0x70180 635 #define DSPBCNTR 0x71180 636 #define DSPCCNTR 0x72180 637 #define DISPLAY_PLANE_ENABLE (1 << 31) 638 #define DISPLAY_PLANE_DISABLE 0 639 #define DISPPLANE_GAMMA_ENABLE (1 << 30) 640 #define DISPPLANE_GAMMA_DISABLE 0 641 #define DISPPLANE_PIXFORMAT_MASK (0xf << 26) 642 #define DISPPLANE_8BPP (0x2 << 26) 643 #define DISPPLANE_15_16BPP (0x4 << 26) 644 #define DISPPLANE_16BPP (0x5 << 26) 645 #define DISPPLANE_32BPP_NO_ALPHA (0x6 << 26) 646 #define DISPPLANE_32BPP (0x7 << 26) 647 #define DISPPLANE_STEREO_ENABLE (1 << 25) 648 #define DISPPLANE_STEREO_DISABLE 0 649 #define DISPPLANE_SEL_PIPE_MASK (1 << 24) 650 #define DISPPLANE_SEL_PIPE_POS 24 651 #define DISPPLANE_SEL_PIPE_A 0 652 #define DISPPLANE_SEL_PIPE_B (1 << 24) 653 #define DISPPLANE_SRC_KEY_ENABLE (1 << 22) 654 #define DISPPLANE_SRC_KEY_DISABLE 0 655 #define DISPPLANE_LINE_DOUBLE (1 << 20) 656 #define DISPPLANE_NO_LINE_DOUBLE 0 657 #define DISPPLANE_STEREO_POLARITY_FIRST 0 658 #define DISPPLANE_STEREO_POLARITY_SECOND (1 << 18) 659 /* plane B only */ 660 #define DISPPLANE_ALPHA_TRANS_ENABLE (1 << 15) 661 #define DISPPLANE_ALPHA_TRANS_DISABLE 0 662 #define DISPPLANE_SPRITE_ABOVE_DISPLAYA 0 663 #define DISPPLANE_SPRITE_ABOVE_OVERLAY (1) 664 #define DISPPLANE_BOTTOM (4) 665 666 #define DSPABASE 0x70184 667 #define DSPALINOFF 0x70184 668 #define DSPASTRIDE 0x70188 669 670 #define DSPBBASE 0x71184 671 #define DSPBLINOFF 0X71184 672 #define DSPBADDR DSPBBASE 673 #define DSPBSTRIDE 0x71188 674 675 #define DSPCBASE 0x72184 676 #define DSPCLINOFF 0x72184 677 #define DSPCSTRIDE 0x72188 678 679 #define DSPAKEYVAL 0x70194 680 #define DSPAKEYMASK 0x70198 681 682 #define DSPAPOS 0x7018C /* reserved */ 683 #define DSPASIZE 0x70190 684 #define DSPBPOS 0x7118C 685 #define DSPBSIZE 0x71190 686 #define DSPCPOS 0x7218C 687 #define DSPCSIZE 0x72190 688 689 #define DSPASURF 0x7019C 690 #define DSPATILEOFF 0x701A4 691 692 #define DSPBSURF 0x7119C 693 #define DSPBTILEOFF 0x711A4 694 695 #define DSPCSURF 0x7219C 696 #define DSPCTILEOFF 0x721A4 697 #define DSPCKEYMAXVAL 0x721A0 698 #define DSPCKEYMINVAL 0x72194 699 #define DSPCKEYMSK 0x72198 700 701 #define VGACNTRL 0x71400 702 #define VGA_DISP_DISABLE (1 << 31) 703 #define VGA_2X_MODE (1 << 30) 704 #define VGA_PIPE_B_SELECT (1 << 29) 705 706 /* 707 * Overlay registers 708 */ 709 #define OV_C_OFFSET 0x08000 710 #define OV_OVADD 0x30000 711 #define OV_DOVASTA 0x30008 712 # define OV_PIPE_SELECT ((1 << 6)|(1 << 7)) 713 # define OV_PIPE_SELECT_POS 6 714 # define OV_PIPE_A 0 715 # define OV_PIPE_C 1 716 #define OV_OGAMC5 0x30010 717 #define OV_OGAMC4 0x30014 718 #define OV_OGAMC3 0x30018 719 #define OV_OGAMC2 0x3001C 720 #define OV_OGAMC1 0x30020 721 #define OV_OGAMC0 0x30024 722 #define OVC_OVADD 0x38000 723 #define OVC_DOVCSTA 0x38008 724 #define OVC_OGAMC5 0x38010 725 #define OVC_OGAMC4 0x38014 726 #define OVC_OGAMC3 0x38018 727 #define OVC_OGAMC2 0x3801C 728 #define OVC_OGAMC1 0x38020 729 #define OVC_OGAMC0 0x38024 730 731 /* 732 * Some BIOS scratch area registers. The 845 (and 830?) store the amount 733 * of video memory available to the BIOS in SWF1. 734 */ 735 #define SWF0 0x71410 736 #define SWF1 0x71414 737 #define SWF2 0x71418 738 #define SWF3 0x7141c 739 #define SWF4 0x71420 740 #define SWF5 0x71424 741 #define SWF6 0x71428 742 743 /* 744 * 855 scratch registers. 745 */ 746 #define SWF00 0x70410 747 #define SWF01 0x70414 748 #define SWF02 0x70418 749 #define SWF03 0x7041c 750 #define SWF04 0x70420 751 #define SWF05 0x70424 752 #define SWF06 0x70428 753 754 #define SWF10 SWF0 755 #define SWF11 SWF1 756 #define SWF12 SWF2 757 #define SWF13 SWF3 758 #define SWF14 SWF4 759 #define SWF15 SWF5 760 #define SWF16 SWF6 761 762 #define SWF30 0x72414 763 #define SWF31 0x72418 764 #define SWF32 0x7241c 765 766 767 /* 768 * Palette registers 769 */ 770 #define PALETTE_A 0x0a000 771 #define PALETTE_B 0x0a800 772 #define PALETTE_C 0x0ac00 773 774 /* Cursor A & B regs */ 775 #define CURACNTR 0x70080 776 #define CURSOR_MODE_DISABLE 0x00 777 #define CURSOR_MODE_64_32B_AX 0x07 778 #define CURSOR_MODE_64_ARGB_AX ((1 << 5) | CURSOR_MODE_64_32B_AX) 779 #define MCURSOR_GAMMA_ENABLE (1 << 26) 780 #define CURABASE 0x70084 781 #define CURAPOS 0x70088 782 #define CURSOR_POS_MASK 0x007FF 783 #define CURSOR_POS_SIGN 0x8000 784 #define CURSOR_X_SHIFT 0 785 #define CURSOR_Y_SHIFT 16 786 #define CURBCNTR 0x700c0 787 #define CURBBASE 0x700c4 788 #define CURBPOS 0x700c8 789 #define CURCCNTR 0x700e0 790 #define CURCBASE 0x700e4 791 #define CURCPOS 0x700e8 792 793 /* 794 * Interrupt Registers 795 */ 796 #define IER 0x020a0 797 #define IIR 0x020a4 798 #define IMR 0x020a8 799 #define ISR 0x020ac 800 801 /* 802 * MOORESTOWN delta registers 803 */ 804 #define MRST_DPLL_A 0x0f014 805 #define MDFLD_DPLL_B 0x0f018 806 #define MDFLD_INPUT_REF_SEL (1 << 14) 807 #define MDFLD_VCO_SEL (1 << 16) 808 #define DPLLA_MODE_LVDS (2 << 26) /* mrst */ 809 #define MDFLD_PLL_LATCHEN (1 << 28) 810 #define MDFLD_PWR_GATE_EN (1 << 30) 811 #define MDFLD_P1_MASK (0x1FF << 17) 812 #define MRST_FPA0 0x0f040 813 #define MRST_FPA1 0x0f044 814 #define MDFLD_DPLL_DIV0 0x0f048 815 #define MDFLD_DPLL_DIV1 0x0f04c 816 #define MRST_PERF_MODE 0x020f4 817 818 /* 819 * MEDFIELD HDMI registers 820 */ 821 #define HDMIPHYMISCCTL 0x61134 822 #define HDMI_PHY_POWER_DOWN 0x7f 823 #define HDMIB_CONTROL 0x61140 824 #define HDMIB_PORT_EN (1 << 31) 825 #define HDMIB_PIPE_B_SELECT (1 << 30) 826 #define HDMIB_NULL_PACKET (1 << 9) 827 #define HDMIB_HDCP_PORT (1 << 5) 828 829 /* #define LVDS 0x61180 */ 830 #define MRST_PANEL_8TO6_DITHER_ENABLE (1 << 25) 831 #define MRST_PANEL_24_DOT_1_FORMAT (1 << 24) 832 #define LVDS_A3_POWER_UP_0_OUTPUT (1 << 6) 833 834 #define MIPI 0x61190 835 #define MIPI_C 0x62190 836 #define MIPI_PORT_EN (1 << 31) 837 /* Turns on border drawing to allow centered display. */ 838 #define SEL_FLOPPED_HSTX (1 << 23) 839 #define PASS_FROM_SPHY_TO_AFE (1 << 16) 840 #define MIPI_BORDER_EN (1 << 15) 841 #define MIPIA_3LANE_MIPIC_1LANE 0x1 842 #define MIPIA_2LANE_MIPIC_2LANE 0x2 843 #define TE_TRIGGER_DSI_PROTOCOL (1 << 2) 844 #define TE_TRIGGER_GPIO_PIN (1 << 3) 845 #define MIPI_TE_COUNT 0x61194 846 847 /* #define PP_CONTROL 0x61204 */ 848 #define POWER_DOWN_ON_RESET (1 << 1) 849 850 /* #define PFIT_CONTROL 0x61230 */ 851 #define PFIT_PIPE_SELECT (3 << 29) 852 #define PFIT_PIPE_SELECT_SHIFT (29) 853 854 /* #define BLC_PWM_CTL 0x61254 */ 855 #define MRST_BACKLIGHT_MODULATION_FREQ_SHIFT (16) 856 #define MRST_BACKLIGHT_MODULATION_FREQ_MASK (0xffff << 16) 857 858 /* #define PIPEACONF 0x70008 */ 859 #define PIPEACONF_PIPE_STATE (1 << 30) 860 /* #define DSPACNTR 0x70180 */ 861 862 #define MRST_DSPABASE 0x7019c 863 #define MRST_DSPBBASE 0x7119c 864 #define MDFLD_DSPCBASE 0x7219c 865 866 /* 867 * Moorestown registers. 868 */ 869 870 /* 871 * MIPI IP registers 872 */ 873 #define MIPIC_REG_OFFSET 0x800 874 875 #define DEVICE_READY_REG 0xb000 876 #define LP_OUTPUT_HOLD (1 << 16) 877 #define EXIT_ULPS_DEV_READY 0x3 878 #define LP_OUTPUT_HOLD_RELEASE 0x810000 879 # define ENTERING_ULPS (2 << 1) 880 # define EXITING_ULPS (1 << 1) 881 # define ULPS_MASK (3 << 1) 882 # define BUS_POSSESSION (1 << 3) 883 #define INTR_STAT_REG 0xb004 884 #define RX_SOT_ERROR (1 << 0) 885 #define RX_SOT_SYNC_ERROR (1 << 1) 886 #define RX_ESCAPE_MODE_ENTRY_ERROR (1 << 3) 887 #define RX_LP_TX_SYNC_ERROR (1 << 4) 888 #define RX_HS_RECEIVE_TIMEOUT_ERROR (1 << 5) 889 #define RX_FALSE_CONTROL_ERROR (1 << 6) 890 #define RX_ECC_SINGLE_BIT_ERROR (1 << 7) 891 #define RX_ECC_MULTI_BIT_ERROR (1 << 8) 892 #define RX_CHECKSUM_ERROR (1 << 9) 893 #define RX_DSI_DATA_TYPE_NOT_RECOGNIZED (1 << 10) 894 #define RX_DSI_VC_ID_INVALID (1 << 11) 895 #define TX_FALSE_CONTROL_ERROR (1 << 12) 896 #define TX_ECC_SINGLE_BIT_ERROR (1 << 13) 897 #define TX_ECC_MULTI_BIT_ERROR (1 << 14) 898 #define TX_CHECKSUM_ERROR (1 << 15) 899 #define TX_DSI_DATA_TYPE_NOT_RECOGNIZED (1 << 16) 900 #define TX_DSI_VC_ID_INVALID (1 << 17) 901 #define HIGH_CONTENTION (1 << 18) 902 #define LOW_CONTENTION (1 << 19) 903 #define DPI_FIFO_UNDER_RUN (1 << 20) 904 #define HS_TX_TIMEOUT (1 << 21) 905 #define LP_RX_TIMEOUT (1 << 22) 906 #define TURN_AROUND_ACK_TIMEOUT (1 << 23) 907 #define ACK_WITH_NO_ERROR (1 << 24) 908 #define HS_GENERIC_WR_FIFO_FULL (1 << 27) 909 #define LP_GENERIC_WR_FIFO_FULL (1 << 28) 910 #define SPL_PKT_SENT (1 << 30) 911 #define INTR_EN_REG 0xb008 912 #define DSI_FUNC_PRG_REG 0xb00c 913 #define DPI_CHANNEL_NUMBER_POS 0x03 914 #define DBI_CHANNEL_NUMBER_POS 0x05 915 #define FMT_DPI_POS 0x07 916 #define FMT_DBI_POS 0x0A 917 #define DBI_DATA_WIDTH_POS 0x0D 918 919 /* DPI PIXEL FORMATS */ 920 #define RGB_565_FMT 0x01 /* RGB 565 FORMAT */ 921 #define RGB_666_FMT 0x02 /* RGB 666 FORMAT */ 922 #define LRGB_666_FMT 0x03 /* RGB LOOSELY PACKED 923 * 666 FORMAT 924 */ 925 #define RGB_888_FMT 0x04 /* RGB 888 FORMAT */ 926 #define VIRTUAL_CHANNEL_NUMBER_0 0x00 /* Virtual channel 0 */ 927 #define VIRTUAL_CHANNEL_NUMBER_1 0x01 /* Virtual channel 1 */ 928 #define VIRTUAL_CHANNEL_NUMBER_2 0x02 /* Virtual channel 2 */ 929 #define VIRTUAL_CHANNEL_NUMBER_3 0x03 /* Virtual channel 3 */ 930 931 #define DBI_NOT_SUPPORTED 0x00 /* command mode 932 * is not supported 933 */ 934 #define DBI_DATA_WIDTH_16BIT 0x01 /* 16 bit data */ 935 #define DBI_DATA_WIDTH_9BIT 0x02 /* 9 bit data */ 936 #define DBI_DATA_WIDTH_8BIT 0x03 /* 8 bit data */ 937 #define DBI_DATA_WIDTH_OPT1 0x04 /* option 1 */ 938 #define DBI_DATA_WIDTH_OPT2 0x05 /* option 2 */ 939 940 #define HS_TX_TIMEOUT_REG 0xb010 941 #define LP_RX_TIMEOUT_REG 0xb014 942 #define TURN_AROUND_TIMEOUT_REG 0xb018 943 #define DEVICE_RESET_REG 0xb01C 944 #define DPI_RESOLUTION_REG 0xb020 945 #define RES_V_POS 0x10 946 #define DBI_RESOLUTION_REG 0xb024 /* Reserved for MDFLD */ 947 #define HORIZ_SYNC_PAD_COUNT_REG 0xb028 948 #define HORIZ_BACK_PORCH_COUNT_REG 0xb02C 949 #define HORIZ_FRONT_PORCH_COUNT_REG 0xb030 950 #define HORIZ_ACTIVE_AREA_COUNT_REG 0xb034 951 #define VERT_SYNC_PAD_COUNT_REG 0xb038 952 #define VERT_BACK_PORCH_COUNT_REG 0xb03c 953 #define VERT_FRONT_PORCH_COUNT_REG 0xb040 954 #define HIGH_LOW_SWITCH_COUNT_REG 0xb044 955 #define DPI_CONTROL_REG 0xb048 956 #define DPI_SHUT_DOWN (1 << 0) 957 #define DPI_TURN_ON (1 << 1) 958 #define DPI_COLOR_MODE_ON (1 << 2) 959 #define DPI_COLOR_MODE_OFF (1 << 3) 960 #define DPI_BACK_LIGHT_ON (1 << 4) 961 #define DPI_BACK_LIGHT_OFF (1 << 5) 962 #define DPI_LP (1 << 6) 963 #define DPI_DATA_REG 0xb04c 964 #define DPI_BACK_LIGHT_ON_DATA 0x07 965 #define DPI_BACK_LIGHT_OFF_DATA 0x17 966 #define INIT_COUNT_REG 0xb050 967 #define MAX_RET_PAK_REG 0xb054 968 #define VIDEO_FMT_REG 0xb058 969 #define COMPLETE_LAST_PCKT (1 << 2) 970 #define EOT_DISABLE_REG 0xb05c 971 #define ENABLE_CLOCK_STOPPING (1 << 1) 972 #define LP_BYTECLK_REG 0xb060 973 #define LP_GEN_DATA_REG 0xb064 974 #define HS_GEN_DATA_REG 0xb068 975 #define LP_GEN_CTRL_REG 0xb06C 976 #define HS_GEN_CTRL_REG 0xb070 977 #define DCS_CHANNEL_NUMBER_POS 0x6 978 #define MCS_COMMANDS_POS 0x8 979 #define WORD_COUNTS_POS 0x8 980 #define MCS_PARAMETER_POS 0x10 981 #define GEN_FIFO_STAT_REG 0xb074 982 #define HS_DATA_FIFO_FULL (1 << 0) 983 #define HS_DATA_FIFO_HALF_EMPTY (1 << 1) 984 #define HS_DATA_FIFO_EMPTY (1 << 2) 985 #define LP_DATA_FIFO_FULL (1 << 8) 986 #define LP_DATA_FIFO_HALF_EMPTY (1 << 9) 987 #define LP_DATA_FIFO_EMPTY (1 << 10) 988 #define HS_CTRL_FIFO_FULL (1 << 16) 989 #define HS_CTRL_FIFO_HALF_EMPTY (1 << 17) 990 #define HS_CTRL_FIFO_EMPTY (1 << 18) 991 #define LP_CTRL_FIFO_FULL (1 << 24) 992 #define LP_CTRL_FIFO_HALF_EMPTY (1 << 25) 993 #define LP_CTRL_FIFO_EMPTY (1 << 26) 994 #define DBI_FIFO_EMPTY (1 << 27) 995 #define DPI_FIFO_EMPTY (1 << 28) 996 #define HS_LS_DBI_ENABLE_REG 0xb078 997 #define TXCLKESC_REG 0xb07c 998 #define DPHY_PARAM_REG 0xb080 999 #define DBI_BW_CTRL_REG 0xb084 1000 #define CLK_LANE_SWT_REG 0xb088 1001 1002 /* 1003 * MIPI Adapter registers 1004 */ 1005 #define MIPI_CONTROL_REG 0xb104 1006 #define MIPI_2X_CLOCK_BITS ((1 << 0) | (1 << 1)) 1007 #define MIPI_DATA_ADDRESS_REG 0xb108 1008 #define MIPI_DATA_LENGTH_REG 0xb10C 1009 #define MIPI_COMMAND_ADDRESS_REG 0xb110 1010 #define MIPI_COMMAND_LENGTH_REG 0xb114 1011 #define MIPI_READ_DATA_RETURN_REG0 0xb118 1012 #define MIPI_READ_DATA_RETURN_REG1 0xb11C 1013 #define MIPI_READ_DATA_RETURN_REG2 0xb120 1014 #define MIPI_READ_DATA_RETURN_REG3 0xb124 1015 #define MIPI_READ_DATA_RETURN_REG4 0xb128 1016 #define MIPI_READ_DATA_RETURN_REG5 0xb12C 1017 #define MIPI_READ_DATA_RETURN_REG6 0xb130 1018 #define MIPI_READ_DATA_RETURN_REG7 0xb134 1019 #define MIPI_READ_DATA_VALID_REG 0xb138 1020 1021 /* DBI COMMANDS */ 1022 #define soft_reset 0x01 1023 /* 1024 * The display module performs a software reset. 1025 * Registers are written with their SW Reset default values. 1026 */ 1027 #define get_power_mode 0x0a 1028 /* 1029 * The display module returns the current power mode 1030 */ 1031 #define get_address_mode 0x0b 1032 /* 1033 * The display module returns the current status. 1034 */ 1035 #define get_pixel_format 0x0c 1036 /* 1037 * This command gets the pixel format for the RGB image data 1038 * used by the interface. 1039 */ 1040 #define get_display_mode 0x0d 1041 /* 1042 * The display module returns the Display Image Mode status. 1043 */ 1044 #define get_signal_mode 0x0e 1045 /* 1046 * The display module returns the Display Signal Mode. 1047 */ 1048 #define get_diagnostic_result 0x0f 1049 /* 1050 * The display module returns the self-diagnostic results following 1051 * a Sleep Out command. 1052 */ 1053 #define enter_sleep_mode 0x10 1054 /* 1055 * This command causes the display module to enter the Sleep mode. 1056 * In this mode, all unnecessary blocks inside the display module are 1057 * disabled except interface communication. This is the lowest power 1058 * mode the display module supports. 1059 */ 1060 #define exit_sleep_mode 0x11 1061 /* 1062 * This command causes the display module to exit Sleep mode. 1063 * All blocks inside the display module are enabled. 1064 */ 1065 #define enter_partial_mode 0x12 1066 /* 1067 * This command causes the display module to enter the Partial Display 1068 * Mode. The Partial Display Mode window is described by the 1069 * set_partial_area command. 1070 */ 1071 #define enter_normal_mode 0x13 1072 /* 1073 * This command causes the display module to enter the Normal mode. 1074 * Normal Mode is defined as Partial Display mode and Scroll mode are off 1075 */ 1076 #define exit_invert_mode 0x20 1077 /* 1078 * This command causes the display module to stop inverting the image 1079 * data on the display device. The frame memory contents remain unchanged. 1080 * No status bits are changed. 1081 */ 1082 #define enter_invert_mode 0x21 1083 /* 1084 * This command causes the display module to invert the image data only on 1085 * the display device. The frame memory contents remain unchanged. 1086 * No status bits are changed. 1087 */ 1088 #define set_gamma_curve 0x26 1089 /* 1090 * This command selects the desired gamma curve for the display device. 1091 * Four fixed gamma curves are defined in section DCS spec. 1092 */ 1093 #define set_display_off 0x28 1094 /* ************************************************************************* *\ 1095 This command causes the display module to stop displaying the image data 1096 on the display device. The frame memory contents remain unchanged. 1097 No status bits are changed. 1098 \* ************************************************************************* */ 1099 #define set_display_on 0x29 1100 /* ************************************************************************* *\ 1101 This command causes the display module to start displaying the image data 1102 on the display device. The frame memory contents remain unchanged. 1103 No status bits are changed. 1104 \* ************************************************************************* */ 1105 #define set_column_address 0x2a 1106 /* 1107 * This command defines the column extent of the frame memory accessed by 1108 * the hostprocessor with the read_memory_continue and 1109 * write_memory_continue commands. 1110 * No status bits are changed. 1111 */ 1112 #define set_page_addr 0x2b 1113 /* 1114 * This command defines the page extent of the frame memory accessed by 1115 * the host processor with the write_memory_continue and 1116 * read_memory_continue command. 1117 * No status bits are changed. 1118 */ 1119 #define write_mem_start 0x2c 1120 /* 1121 * This command transfers image data from the host processor to the 1122 * display modules frame memory starting at the pixel location specified 1123 * by preceding set_column_address and set_page_address commands. 1124 */ 1125 #define set_partial_area 0x30 1126 /* 1127 * This command defines the Partial Display mode s display area. 1128 * There are two parameters associated with this command, the first 1129 * defines the Start Row (SR) and the second the End Row (ER). SR and ER 1130 * refer to the Frame Memory Line Pointer. 1131 */ 1132 #define set_scroll_area 0x33 1133 /* 1134 * This command defines the display modules Vertical Scrolling Area. 1135 */ 1136 #define set_tear_off 0x34 1137 /* 1138 * This command turns off the display modules Tearing Effect output 1139 * signal on the TE signal line. 1140 */ 1141 #define set_tear_on 0x35 1142 /* 1143 * This command turns on the display modules Tearing Effect output signal 1144 * on the TE signal line. 1145 */ 1146 #define set_address_mode 0x36 1147 /* 1148 * This command sets the data order for transfers from the host processor 1149 * to display modules frame memory,bits B[7:5] and B3, and from the 1150 * display modules frame memory to the display device, bits B[2:0] and B4. 1151 */ 1152 #define set_scroll_start 0x37 1153 /* 1154 * This command sets the start of the vertical scrolling area in the frame 1155 * memory. The vertical scrolling area is fully defined when this command 1156 * is used with the set_scroll_area command The set_scroll_start command 1157 * has one parameter, the Vertical Scroll Pointer. The VSP defines the 1158 * line in the frame memory that is written to the display device as the 1159 * first line of the vertical scroll area. 1160 */ 1161 #define exit_idle_mode 0x38 1162 /* 1163 * This command causes the display module to exit Idle mode. 1164 */ 1165 #define enter_idle_mode 0x39 1166 /* 1167 * This command causes the display module to enter Idle Mode. 1168 * In Idle Mode, color expression is reduced. Colors are shown on the 1169 * display device using the MSB of each of the R, G and B color 1170 * components in the frame memory 1171 */ 1172 #define set_pixel_format 0x3a 1173 /* 1174 * This command sets the pixel format for the RGB image data used by the 1175 * interface. 1176 * Bits D[6:4] DPI Pixel Format Definition 1177 * Bits D[2:0] DBI Pixel Format Definition 1178 * Bits D7 and D3 are not used. 1179 */ 1180 #define DCS_PIXEL_FORMAT_3bpp 0x1 1181 #define DCS_PIXEL_FORMAT_8bpp 0x2 1182 #define DCS_PIXEL_FORMAT_12bpp 0x3 1183 #define DCS_PIXEL_FORMAT_16bpp 0x5 1184 #define DCS_PIXEL_FORMAT_18bpp 0x6 1185 #define DCS_PIXEL_FORMAT_24bpp 0x7 1186 1187 #define write_mem_cont 0x3c 1188 1189 /* 1190 * This command transfers image data from the host processor to the 1191 * display module's frame memory continuing from the pixel location 1192 * following the previous write_memory_continue or write_memory_start 1193 * command. 1194 */ 1195 #define set_tear_scanline 0x44 1196 /* 1197 * This command turns on the display modules Tearing Effect output signal 1198 * on the TE signal line when the display module reaches line N. 1199 */ 1200 #define get_scanline 0x45 1201 /* 1202 * The display module returns the current scanline, N, used to update the 1203 * display device. The total number of scanlines on a display device is 1204 * defined as VSYNC + VBP + VACT + VFP.The first scanline is defined as 1205 * the first line of V Sync and is denoted as Line 0. 1206 * When in Sleep Mode, the value returned by get_scanline is undefined. 1207 */ 1208 1209 /* MCS or Generic COMMANDS */ 1210 /* MCS/generic data type */ 1211 #define GEN_SHORT_WRITE_0 0x03 /* generic short write, no parameters */ 1212 #define GEN_SHORT_WRITE_1 0x13 /* generic short write, 1 parameters */ 1213 #define GEN_SHORT_WRITE_2 0x23 /* generic short write, 2 parameters */ 1214 #define GEN_READ_0 0x04 /* generic read, no parameters */ 1215 #define GEN_READ_1 0x14 /* generic read, 1 parameters */ 1216 #define GEN_READ_2 0x24 /* generic read, 2 parameters */ 1217 #define GEN_LONG_WRITE 0x29 /* generic long write */ 1218 #define MCS_SHORT_WRITE_0 0x05 /* MCS short write, no parameters */ 1219 #define MCS_SHORT_WRITE_1 0x15 /* MCS short write, 1 parameters */ 1220 #define MCS_READ 0x06 /* MCS read, no parameters */ 1221 #define MCS_LONG_WRITE 0x39 /* MCS long write */ 1222 /* MCS/generic commands */ 1223 /* TPO MCS */ 1224 #define write_display_profile 0x50 1225 #define write_display_brightness 0x51 1226 #define write_ctrl_display 0x53 1227 #define write_ctrl_cabc 0x55 1228 #define UI_IMAGE 0x01 1229 #define STILL_IMAGE 0x02 1230 #define MOVING_IMAGE 0x03 1231 #define write_hysteresis 0x57 1232 #define write_gamma_setting 0x58 1233 #define write_cabc_min_bright 0x5e 1234 #define write_kbbc_profile 0x60 1235 /* TMD MCS */ 1236 #define tmd_write_display_brightness 0x8c 1237 1238 /* 1239 * This command is used to control ambient light, panel backlight 1240 * brightness and gamma settings. 1241 */ 1242 #define BRIGHT_CNTL_BLOCK_ON (1 << 5) 1243 #define AMBIENT_LIGHT_SENSE_ON (1 << 4) 1244 #define DISPLAY_DIMMING_ON (1 << 3) 1245 #define BACKLIGHT_ON (1 << 2) 1246 #define DISPLAY_BRIGHTNESS_AUTO (1 << 1) 1247 #define GAMMA_AUTO (1 << 0) 1248 1249 /* DCS Interface Pixel Formats */ 1250 #define DCS_PIXEL_FORMAT_3BPP 0x1 1251 #define DCS_PIXEL_FORMAT_8BPP 0x2 1252 #define DCS_PIXEL_FORMAT_12BPP 0x3 1253 #define DCS_PIXEL_FORMAT_16BPP 0x5 1254 #define DCS_PIXEL_FORMAT_18BPP 0x6 1255 #define DCS_PIXEL_FORMAT_24BPP 0x7 1256 /* ONE PARAMETER READ DATA */ 1257 #define addr_mode_data 0xfc 1258 #define diag_res_data 0x00 1259 #define disp_mode_data 0x23 1260 #define pxl_fmt_data 0x77 1261 #define pwr_mode_data 0x74 1262 #define sig_mode_data 0x00 1263 /* TWO PARAMETERS READ DATA */ 1264 #define scanline_data1 0xff 1265 #define scanline_data2 0xff 1266 #define NON_BURST_MODE_SYNC_PULSE 0x01 /* Non Burst Mode 1267 * with Sync Pulse 1268 */ 1269 #define NON_BURST_MODE_SYNC_EVENTS 0x02 /* Non Burst Mode 1270 * with Sync events 1271 */ 1272 #define BURST_MODE 0x03 /* Burst Mode */ 1273 #define DBI_COMMAND_BUFFER_SIZE 0x240 /* 0x32 */ /* 0x120 */ 1274 /* Allocate at least 1275 * 0x100 Byte with 32 1276 * byte alignment 1277 */ 1278 #define DBI_DATA_BUFFER_SIZE 0x120 /* Allocate at least 1279 * 0x100 Byte with 32 1280 * byte alignment 1281 */ 1282 #define DBI_CB_TIME_OUT 0xFFFF 1283 1284 #define GEN_FB_TIME_OUT 2000 1285 1286 #define SKU_83 0x01 1287 #define SKU_100 0x02 1288 #define SKU_100L 0x04 1289 #define SKU_BYPASS 0x08 1290 1291 /* Some handy macros for playing with bitfields. */ 1292 #define PSB_MASK(high, low) (((1<<((high)-(low)+1))-1)<<(low)) 1293 #define SET_FIELD(value, field) (((value) << field ## _SHIFT) & field ## _MASK) 1294 #define GET_FIELD(word, field) (((word) & field ## _MASK) >> field ## _SHIFT) 1295 1296 #define _PIPE(pipe, a, b) ((a) + (pipe)*((b)-(a))) 1297 1298 /* PCI config space */ 1299 1300 #define SB_PCKT 0x02100 /* cedarview */ 1301 # define SB_OPCODE_MASK PSB_MASK(31, 16) 1302 # define SB_OPCODE_SHIFT 16 1303 # define SB_OPCODE_READ 0 1304 # define SB_OPCODE_WRITE 1 1305 # define SB_DEST_MASK PSB_MASK(15, 8) 1306 # define SB_DEST_SHIFT 8 1307 # define SB_DEST_DPLL 0x88 1308 # define SB_BYTE_ENABLE_MASK PSB_MASK(7, 4) 1309 # define SB_BYTE_ENABLE_SHIFT 4 1310 # define SB_BUSY (1 << 0) 1311 1312 #define DSPCLK_GATE_D 0x6200 1313 # define VRHUNIT_CLOCK_GATE_DISABLE (1 << 28) /* Fixed value on CDV */ 1314 # define DPOUNIT_CLOCK_GATE_DISABLE (1 << 11) 1315 # define DPIOUNIT_CLOCK_GATE_DISABLE (1 << 6) 1316 # define DPUNIT_PIPEB_GATE_DISABLE (1 << 30) 1317 # define DPUNIT_PIPEA_GATE_DISABLE (1 << 25) 1318 # define DPCUNIT_CLOCK_GATE_DISABLE (1 << 24) 1319 # define DPLSUNIT_CLOCK_GATE_DISABLE (1 << 13) 1320 1321 #define RAMCLK_GATE_D 0x6210 1322 1323 /* 32-bit value read/written from the DPIO reg. */ 1324 #define SB_DATA 0x02104 /* cedarview */ 1325 /* 32-bit address of the DPIO reg to be read/written. */ 1326 #define SB_ADDR 0x02108 /* cedarview */ 1327 #define DPIO_CFG 0x02110 /* cedarview */ 1328 # define DPIO_MODE_SELECT_1 (1 << 3) 1329 # define DPIO_MODE_SELECT_0 (1 << 2) 1330 # define DPIO_SFR_BYPASS (1 << 1) 1331 /* reset is active low */ 1332 # define DPIO_CMN_RESET_N (1 << 0) 1333 1334 /* Cedarview sideband registers */ 1335 #define _SB_M_A 0x8008 1336 #define _SB_M_B 0x8028 1337 #define SB_M(pipe) _PIPE(pipe, _SB_M_A, _SB_M_B) 1338 # define SB_M_DIVIDER_MASK (0xFF << 24) 1339 # define SB_M_DIVIDER_SHIFT 24 1340 1341 #define _SB_N_VCO_A 0x8014 1342 #define _SB_N_VCO_B 0x8034 1343 #define SB_N_VCO(pipe) _PIPE(pipe, _SB_N_VCO_A, _SB_N_VCO_B) 1344 #define SB_N_VCO_SEL_MASK PSB_MASK(31, 30) 1345 #define SB_N_VCO_SEL_SHIFT 30 1346 #define SB_N_DIVIDER_MASK PSB_MASK(29, 26) 1347 #define SB_N_DIVIDER_SHIFT 26 1348 #define SB_N_CB_TUNE_MASK PSB_MASK(25, 24) 1349 #define SB_N_CB_TUNE_SHIFT 24 1350 1351 /* the bit 14:13 is used to select between the different reference clock for Pipe A/B */ 1352 #define SB_REF_DPLLA 0x8010 1353 #define SB_REF_DPLLB 0x8030 1354 #define REF_CLK_MASK (0x3 << 13) 1355 #define REF_CLK_CORE (0 << 13) 1356 #define REF_CLK_DPLL (1 << 13) 1357 #define REF_CLK_DPLLA (2 << 13) 1358 /* For the DPLL B, it will use the reference clk from DPLL A when using (2 << 13) */ 1359 1360 #define _SB_REF_A 0x8018 1361 #define _SB_REF_B 0x8038 1362 #define SB_REF_SFR(pipe) _PIPE(pipe, _SB_REF_A, _SB_REF_B) 1363 1364 #define _SB_P_A 0x801c 1365 #define _SB_P_B 0x803c 1366 #define SB_P(pipe) _PIPE(pipe, _SB_P_A, _SB_P_B) 1367 #define SB_P2_DIVIDER_MASK PSB_MASK(31, 30) 1368 #define SB_P2_DIVIDER_SHIFT 30 1369 #define SB_P2_10 0 /* HDMI, DP, DAC */ 1370 #define SB_P2_5 1 /* DAC */ 1371 #define SB_P2_14 2 /* LVDS single */ 1372 #define SB_P2_7 3 /* LVDS double */ 1373 #define SB_P1_DIVIDER_MASK PSB_MASK(15, 12) 1374 #define SB_P1_DIVIDER_SHIFT 12 1375 1376 #define PSB_LANE0 0x120 1377 #define PSB_LANE1 0x220 1378 #define PSB_LANE2 0x2320 1379 #define PSB_LANE3 0x2420 1380 1381 #define LANE_PLL_MASK (0x7 << 20) 1382 #define LANE_PLL_ENABLE (0x3 << 20) 1383 #define LANE_PLL_PIPE(p) (((p) == 0) ? (1 << 21) : (0 << 21)) 1384 1385 #define DP_B 0x64100 1386 #define DP_C 0x64200 1387 1388 #define DP_PORT_EN (1 << 31) 1389 #define DP_PIPEB_SELECT (1 << 30) 1390 #define DP_PIPE_MASK (1 << 30) 1391 1392 /* Link training mode - select a suitable mode for each stage */ 1393 #define DP_LINK_TRAIN_PAT_1 (0 << 28) 1394 #define DP_LINK_TRAIN_PAT_2 (1 << 28) 1395 #define DP_LINK_TRAIN_PAT_IDLE (2 << 28) 1396 #define DP_LINK_TRAIN_OFF (3 << 28) 1397 #define DP_LINK_TRAIN_MASK (3 << 28) 1398 #define DP_LINK_TRAIN_SHIFT 28 1399 1400 /* Signal voltages. These are mostly controlled by the other end */ 1401 #define DP_VOLTAGE_0_4 (0 << 25) 1402 #define DP_VOLTAGE_0_6 (1 << 25) 1403 #define DP_VOLTAGE_0_8 (2 << 25) 1404 #define DP_VOLTAGE_1_2 (3 << 25) 1405 #define DP_VOLTAGE_MASK (7 << 25) 1406 #define DP_VOLTAGE_SHIFT 25 1407 1408 /* Signal pre-emphasis levels, like voltages, the other end tells us what 1409 * they want 1410 */ 1411 #define DP_PRE_EMPHASIS_0 (0 << 22) 1412 #define DP_PRE_EMPHASIS_3_5 (1 << 22) 1413 #define DP_PRE_EMPHASIS_6 (2 << 22) 1414 #define DP_PRE_EMPHASIS_9_5 (3 << 22) 1415 #define DP_PRE_EMPHASIS_MASK (7 << 22) 1416 #define DP_PRE_EMPHASIS_SHIFT 22 1417 1418 /* How many wires to use. I guess 3 was too hard */ 1419 #define DP_PORT_WIDTH_1 (0 << 19) 1420 #define DP_PORT_WIDTH_2 (1 << 19) 1421 #define DP_PORT_WIDTH_4 (3 << 19) 1422 #define DP_PORT_WIDTH_MASK (7 << 19) 1423 1424 /* Mystic DPCD version 1.1 special mode */ 1425 #define DP_ENHANCED_FRAMING (1 << 18) 1426 1427 /** locked once port is enabled */ 1428 #define DP_PORT_REVERSAL (1 << 15) 1429 1430 /** sends the clock on lane 15 of the PEG for debug */ 1431 #define DP_CLOCK_OUTPUT_ENABLE (1 << 13) 1432 1433 #define DP_SCRAMBLING_DISABLE (1 << 12) 1434 #define DP_SCRAMBLING_DISABLE_IRONLAKE (1 << 7) 1435 1436 /** limit RGB values to avoid confusing TVs */ 1437 #define DP_COLOR_RANGE_16_235 (1 << 8) 1438 1439 /** Turn on the audio link */ 1440 #define DP_AUDIO_OUTPUT_ENABLE (1 << 6) 1441 1442 /** vs and hs sync polarity */ 1443 #define DP_SYNC_VS_HIGH (1 << 4) 1444 #define DP_SYNC_HS_HIGH (1 << 3) 1445 1446 /** A fantasy */ 1447 #define DP_DETECTED (1 << 2) 1448 1449 /** The aux channel provides a way to talk to the 1450 * signal sink for DDC etc. Max packet size supported 1451 * is 20 bytes in each direction, hence the 5 fixed 1452 * data registers 1453 */ 1454 #define DPB_AUX_CH_CTL 0x64110 1455 #define DPB_AUX_CH_DATA1 0x64114 1456 #define DPB_AUX_CH_DATA2 0x64118 1457 #define DPB_AUX_CH_DATA3 0x6411c 1458 #define DPB_AUX_CH_DATA4 0x64120 1459 #define DPB_AUX_CH_DATA5 0x64124 1460 1461 #define DPC_AUX_CH_CTL 0x64210 1462 #define DPC_AUX_CH_DATA1 0x64214 1463 #define DPC_AUX_CH_DATA2 0x64218 1464 #define DPC_AUX_CH_DATA3 0x6421c 1465 #define DPC_AUX_CH_DATA4 0x64220 1466 #define DPC_AUX_CH_DATA5 0x64224 1467 1468 #define DP_AUX_CH_CTL_SEND_BUSY (1 << 31) 1469 #define DP_AUX_CH_CTL_DONE (1 << 30) 1470 #define DP_AUX_CH_CTL_INTERRUPT (1 << 29) 1471 #define DP_AUX_CH_CTL_TIME_OUT_ERROR (1 << 28) 1472 #define DP_AUX_CH_CTL_TIME_OUT_400us (0 << 26) 1473 #define DP_AUX_CH_CTL_TIME_OUT_600us (1 << 26) 1474 #define DP_AUX_CH_CTL_TIME_OUT_800us (2 << 26) 1475 #define DP_AUX_CH_CTL_TIME_OUT_1600us (3 << 26) 1476 #define DP_AUX_CH_CTL_TIME_OUT_MASK (3 << 26) 1477 #define DP_AUX_CH_CTL_RECEIVE_ERROR (1 << 25) 1478 #define DP_AUX_CH_CTL_MESSAGE_SIZE_MASK (0x1f << 20) 1479 #define DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT 20 1480 #define DP_AUX_CH_CTL_PRECHARGE_2US_MASK (0xf << 16) 1481 #define DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT 16 1482 #define DP_AUX_CH_CTL_AUX_AKSV_SELECT (1 << 15) 1483 #define DP_AUX_CH_CTL_MANCHESTER_TEST (1 << 14) 1484 #define DP_AUX_CH_CTL_SYNC_TEST (1 << 13) 1485 #define DP_AUX_CH_CTL_DEGLITCH_TEST (1 << 12) 1486 #define DP_AUX_CH_CTL_PRECHARGE_TEST (1 << 11) 1487 #define DP_AUX_CH_CTL_BIT_CLOCK_2X_MASK (0x7ff) 1488 #define DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT 0 1489 1490 /* 1491 * Computing GMCH M and N values for the Display Port link 1492 * 1493 * GMCH M/N = dot clock * bytes per pixel / ls_clk * # of lanes 1494 * 1495 * ls_clk (we assume) is the DP link clock (1.62 or 2.7 GHz) 1496 * 1497 * The GMCH value is used internally 1498 * 1499 * bytes_per_pixel is the number of bytes coming out of the plane, 1500 * which is after the LUTs, so we want the bytes for our color format. 1501 * For our current usage, this is always 3, one byte for R, G and B. 1502 */ 1503 1504 #define _PIPEA_GMCH_DATA_M 0x70050 1505 #define _PIPEB_GMCH_DATA_M 0x71050 1506 1507 /* Transfer unit size for display port - 1, default is 0x3f (for TU size 64) */ 1508 #define PIPE_GMCH_DATA_M_TU_SIZE_MASK (0x3f << 25) 1509 #define PIPE_GMCH_DATA_M_TU_SIZE_SHIFT 25 1510 1511 #define PIPE_GMCH_DATA_M_MASK (0xffffff) 1512 1513 #define _PIPEA_GMCH_DATA_N 0x70054 1514 #define _PIPEB_GMCH_DATA_N 0x71054 1515 #define PIPE_GMCH_DATA_N_MASK (0xffffff) 1516 1517 /* 1518 * Computing Link M and N values for the Display Port link 1519 * 1520 * Link M / N = pixel_clock / ls_clk 1521 * 1522 * (the DP spec calls pixel_clock the 'strm_clk') 1523 * 1524 * The Link value is transmitted in the Main Stream 1525 * Attributes and VB-ID. 1526 */ 1527 1528 #define _PIPEA_DP_LINK_M 0x70060 1529 #define _PIPEB_DP_LINK_M 0x71060 1530 #define PIPEA_DP_LINK_M_MASK (0xffffff) 1531 1532 #define _PIPEA_DP_LINK_N 0x70064 1533 #define _PIPEB_DP_LINK_N 0x71064 1534 #define PIPEA_DP_LINK_N_MASK (0xffffff) 1535 1536 #define PIPE_GMCH_DATA_M(pipe) _PIPE(pipe, _PIPEA_GMCH_DATA_M, _PIPEB_GMCH_DATA_M) 1537 #define PIPE_GMCH_DATA_N(pipe) _PIPE(pipe, _PIPEA_GMCH_DATA_N, _PIPEB_GMCH_DATA_N) 1538 #define PIPE_DP_LINK_M(pipe) _PIPE(pipe, _PIPEA_DP_LINK_M, _PIPEB_DP_LINK_M) 1539 #define PIPE_DP_LINK_N(pipe) _PIPE(pipe, _PIPEA_DP_LINK_N, _PIPEB_DP_LINK_N) 1540 1541 #define PIPE_BPC_MASK (7 << 5) 1542 #define PIPE_8BPC (0 << 5) 1543 #define PIPE_10BPC (1 << 5) 1544 #define PIPE_6BPC (2 << 5) 1545 1546 #endif 1547