1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Device Tree Source for common parts of Salvator-X board variants 4 * 5 * Copyright (C) 2015-2016 Renesas Electronics Corp. 6 */ 7 8/* 9 * SSI-AK4613 10 * 11 * This command is required when Playback/Capture 12 * 13 * amixer set "DVC Out" 100% 14 * amixer set "DVC In" 100% 15 * 16 * You can use Mute 17 * 18 * amixer set "DVC Out Mute" on 19 * amixer set "DVC In Mute" on 20 * 21 * You can use Volume Ramp 22 * 23 * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps" 24 * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps" 25 * amixer set "DVC Out Ramp" on 26 * aplay xxx.wav & 27 * amixer set "DVC Out" 80% // Volume Down 28 * amixer set "DVC Out" 100% // Volume Up 29 */ 30 31#include <dt-bindings/gpio/gpio.h> 32#include <dt-bindings/input/input.h> 33 34/ { 35 aliases { 36 serial0 = &scif2; 37 serial1 = &hscif1; 38 ethernet0 = &avb; 39 }; 40 41 chosen { 42 bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp"; 43 stdout-path = "serial0:115200n8"; 44 }; 45 46 audio_clkout: audio-clkout { 47 /* 48 * This is same as <&rcar_sound 0> 49 * but needed to avoid cs2000/rcar_sound probe dead-lock 50 */ 51 compatible = "fixed-clock"; 52 #clock-cells = <0>; 53 clock-frequency = <12288000>; 54 }; 55 56 backlight: backlight { 57 compatible = "pwm-backlight"; 58 pwms = <&pwm1 0 50000>; 59 60 brightness-levels = <256 128 64 16 8 4 0>; 61 default-brightness-level = <6>; 62 63 power-supply = <®_12v>; 64 enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; 65 }; 66 67 cvbs-in { 68 compatible = "composite-video-connector"; 69 label = "CVBS IN"; 70 71 port { 72 cvbs_con: endpoint { 73 remote-endpoint = <&adv7482_ain7>; 74 }; 75 }; 76 }; 77 78 hdmi-in { 79 compatible = "hdmi-connector"; 80 label = "HDMI IN"; 81 type = "a"; 82 83 port { 84 hdmi_in_con: endpoint { 85 remote-endpoint = <&adv7482_hdmi>; 86 }; 87 }; 88 }; 89 90 keys { 91 compatible = "gpio-keys"; 92 93 pinctrl-0 = <&keys_pins>; 94 pinctrl-names = "default"; 95 96 key-1 { 97 gpios = <&gpio5 17 GPIO_ACTIVE_LOW>; 98 linux,code = <KEY_1>; 99 label = "SW4-1"; 100 wakeup-source; 101 debounce-interval = <20>; 102 }; 103 key-2 { 104 gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; 105 linux,code = <KEY_2>; 106 label = "SW4-2"; 107 wakeup-source; 108 debounce-interval = <20>; 109 }; 110 key-3 { 111 gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; 112 linux,code = <KEY_3>; 113 label = "SW4-3"; 114 wakeup-source; 115 debounce-interval = <20>; 116 }; 117 key-4 { 118 gpios = <&gpio5 23 GPIO_ACTIVE_LOW>; 119 linux,code = <KEY_4>; 120 label = "SW4-4"; 121 wakeup-source; 122 debounce-interval = <20>; 123 }; 124 key-a { 125 gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; 126 linux,code = <KEY_A>; 127 label = "TSW0"; 128 wakeup-source; 129 debounce-interval = <20>; 130 }; 131 key-b { 132 gpios = <&gpio6 12 GPIO_ACTIVE_LOW>; 133 linux,code = <KEY_B>; 134 label = "TSW1"; 135 wakeup-source; 136 debounce-interval = <20>; 137 }; 138 key-c { 139 gpios = <&gpio6 13 GPIO_ACTIVE_LOW>; 140 linux,code = <KEY_C>; 141 label = "TSW2"; 142 wakeup-source; 143 debounce-interval = <20>; 144 }; 145 }; 146 147 reg_1p8v: regulator0 { 148 compatible = "regulator-fixed"; 149 regulator-name = "fixed-1.8V"; 150 regulator-min-microvolt = <1800000>; 151 regulator-max-microvolt = <1800000>; 152 regulator-boot-on; 153 regulator-always-on; 154 }; 155 156 reg_3p3v: regulator1 { 157 compatible = "regulator-fixed"; 158 regulator-name = "fixed-3.3V"; 159 regulator-min-microvolt = <3300000>; 160 regulator-max-microvolt = <3300000>; 161 regulator-boot-on; 162 regulator-always-on; 163 }; 164 165 reg_12v: regulator2 { 166 compatible = "regulator-fixed"; 167 regulator-name = "fixed-12V"; 168 regulator-min-microvolt = <12000000>; 169 regulator-max-microvolt = <12000000>; 170 regulator-boot-on; 171 regulator-always-on; 172 }; 173 174 sound_card: sound { 175 compatible = "audio-graph-card"; 176 177 label = "rcar-sound"; 178 179 dais = <&rsnd_port0>; 180 }; 181 182 vbus0_usb2: regulator-vbus0-usb2 { 183 compatible = "regulator-fixed"; 184 185 regulator-name = "USB20_VBUS0"; 186 regulator-min-microvolt = <5000000>; 187 regulator-max-microvolt = <5000000>; 188 189 gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>; 190 enable-active-high; 191 }; 192 193 vcc_sdhi0: regulator-vcc-sdhi0 { 194 compatible = "regulator-fixed"; 195 196 regulator-name = "SDHI0 Vcc"; 197 regulator-min-microvolt = <3300000>; 198 regulator-max-microvolt = <3300000>; 199 200 gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>; 201 enable-active-high; 202 }; 203 204 vccq_sdhi0: regulator-vccq-sdhi0 { 205 compatible = "regulator-gpio"; 206 207 regulator-name = "SDHI0 VccQ"; 208 regulator-min-microvolt = <1800000>; 209 regulator-max-microvolt = <3300000>; 210 211 gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; 212 gpios-states = <1>; 213 states = <3300000 1 214 1800000 0>; 215 }; 216 217 vcc_sdhi3: regulator-vcc-sdhi3 { 218 compatible = "regulator-fixed"; 219 220 regulator-name = "SDHI3 Vcc"; 221 regulator-min-microvolt = <3300000>; 222 regulator-max-microvolt = <3300000>; 223 224 gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>; 225 enable-active-high; 226 }; 227 228 vccq_sdhi3: regulator-vccq-sdhi3 { 229 compatible = "regulator-gpio"; 230 231 regulator-name = "SDHI3 VccQ"; 232 regulator-min-microvolt = <1800000>; 233 regulator-max-microvolt = <3300000>; 234 235 gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; 236 gpios-states = <1>; 237 states = <3300000 1 238 1800000 0>; 239 }; 240 241 hdmi0-out { 242 compatible = "hdmi-connector"; 243 label = "HDMI0 OUT"; 244 type = "a"; 245 246 port { 247 hdmi0_con: endpoint { 248 }; 249 }; 250 }; 251 252 hdmi1-out { 253 compatible = "hdmi-connector"; 254 label = "HDMI1 OUT"; 255 type = "a"; 256 257 port { 258 hdmi1_con: endpoint { 259 }; 260 }; 261 }; 262 263 vga { 264 compatible = "vga-connector"; 265 266 port { 267 vga_in: endpoint { 268 remote-endpoint = <&adv7123_out>; 269 }; 270 }; 271 }; 272 273 vga-encoder { 274 compatible = "adi,adv7123"; 275 276 ports { 277 #address-cells = <1>; 278 #size-cells = <0>; 279 280 port@0 { 281 reg = <0>; 282 adv7123_in: endpoint { 283 remote-endpoint = <&du_out_rgb>; 284 }; 285 }; 286 port@1 { 287 reg = <1>; 288 adv7123_out: endpoint { 289 remote-endpoint = <&vga_in>; 290 }; 291 }; 292 }; 293 }; 294 295 x12_clk: x12 { 296 compatible = "fixed-clock"; 297 #clock-cells = <0>; 298 clock-frequency = <24576000>; 299 }; 300 301 /* External DU dot clocks */ 302 x21_clk: x21-clock { 303 compatible = "fixed-clock"; 304 #clock-cells = <0>; 305 clock-frequency = <33000000>; 306 }; 307 308 x22_clk: x22-clock { 309 compatible = "fixed-clock"; 310 #clock-cells = <0>; 311 clock-frequency = <33000000>; 312 }; 313 314 x23_clk: x23-clock { 315 compatible = "fixed-clock"; 316 #clock-cells = <0>; 317 clock-frequency = <25000000>; 318 }; 319}; 320 321&audio_clk_a { 322 clock-frequency = <22579200>; 323}; 324 325&avb { 326 pinctrl-0 = <&avb_pins>; 327 pinctrl-names = "default"; 328 phy-handle = <&phy0>; 329 phy-mode = "rgmii-txid"; 330 status = "okay"; 331 332 phy0: ethernet-phy@0 { 333 rxc-skew-ps = <1500>; 334 reg = <0>; 335 interrupt-parent = <&gpio2>; 336 interrupts = <11 IRQ_TYPE_LEVEL_LOW>; 337 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; 338 }; 339}; 340 341&csi20 { 342 status = "okay"; 343 344 ports { 345 port@0 { 346 reg = <0>; 347 csi20_in: endpoint { 348 clock-lanes = <0>; 349 data-lanes = <1>; 350 remote-endpoint = <&adv7482_txb>; 351 }; 352 }; 353 }; 354}; 355 356&csi40 { 357 status = "okay"; 358 359 ports { 360 port@0 { 361 reg = <0>; 362 363 csi40_in: endpoint { 364 clock-lanes = <0>; 365 data-lanes = <1 2 3 4>; 366 remote-endpoint = <&adv7482_txa>; 367 }; 368 }; 369 }; 370}; 371 372&du { 373 pinctrl-0 = <&du_pins>; 374 pinctrl-names = "default"; 375 status = "okay"; 376 377 ports { 378 port@0 { 379 endpoint { 380 remote-endpoint = <&adv7123_in>; 381 }; 382 }; 383 }; 384}; 385 386&ehci0 { 387 dr_mode = "otg"; 388 status = "okay"; 389}; 390 391&ehci1 { 392 status = "okay"; 393}; 394 395&extalr_clk { 396 clock-frequency = <32768>; 397}; 398 399&hscif1 { 400 pinctrl-0 = <&hscif1_pins>; 401 pinctrl-names = "default"; 402 403 uart-has-rtscts; 404 /* Please only enable hscif1 or scif1 */ 405 status = "okay"; 406}; 407 408&hsusb { 409 dr_mode = "otg"; 410 status = "okay"; 411}; 412 413&i2c2 { 414 pinctrl-0 = <&i2c2_pins>; 415 pinctrl-names = "default"; 416 417 status = "okay"; 418 419 clock-frequency = <100000>; 420 421 ak4613: codec@10 { 422 compatible = "asahi-kasei,ak4613"; 423 #sound-dai-cells = <0>; 424 reg = <0x10>; 425 clocks = <&rcar_sound 3>; 426 427 asahi-kasei,in1-single-end; 428 asahi-kasei,in2-single-end; 429 asahi-kasei,out1-single-end; 430 asahi-kasei,out2-single-end; 431 asahi-kasei,out3-single-end; 432 asahi-kasei,out4-single-end; 433 asahi-kasei,out5-single-end; 434 asahi-kasei,out6-single-end; 435 436 port { 437 ak4613_endpoint: endpoint { 438 remote-endpoint = <&rsnd_endpoint0>; 439 }; 440 }; 441 }; 442 443 cs2000: clk_multiplier@4f { 444 #clock-cells = <0>; 445 compatible = "cirrus,cs2000-cp"; 446 reg = <0x4f>; 447 clocks = <&audio_clkout>, <&x12_clk>; 448 clock-names = "clk_in", "ref_clk"; 449 450 assigned-clocks = <&cs2000>; 451 assigned-clock-rates = <24576000>; /* 1/1 divide */ 452 }; 453}; 454 455&i2c4 { 456 status = "okay"; 457 458 pca9654: gpio@20 { 459 compatible = "onnn,pca9654"; 460 reg = <0x20>; 461 gpio-controller; 462 #gpio-cells = <2>; 463 }; 464 465 csa_vdd: adc@7c { 466 compatible = "maxim,max9611"; 467 reg = <0x7c>; 468 469 shunt-resistor-micro-ohms = <5000>; 470 }; 471 472 csa_dvfs: adc@7f { 473 compatible = "maxim,max9611"; 474 reg = <0x7f>; 475 476 shunt-resistor-micro-ohms = <5000>; 477 }; 478 479 video-receiver@70 { 480 compatible = "adi,adv7482"; 481 reg = <0x70 0x71 0x72 0x73 0x74 0x75 482 0x60 0x61 0x62 0x63 0x64 0x65>; 483 reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater", 484 "infoframe", "cbus", "cec", "sdp", "txa", "txb" ; 485 486 #address-cells = <1>; 487 #size-cells = <0>; 488 489 interrupt-parent = <&gpio6>; 490 interrupt-names = "intrq1", "intrq2"; 491 interrupts = <30 IRQ_TYPE_LEVEL_LOW>, 492 <31 IRQ_TYPE_LEVEL_LOW>; 493 494 port@7 { 495 reg = <7>; 496 497 adv7482_ain7: endpoint { 498 remote-endpoint = <&cvbs_con>; 499 }; 500 }; 501 502 port@8 { 503 reg = <8>; 504 505 adv7482_hdmi: endpoint { 506 remote-endpoint = <&hdmi_in_con>; 507 }; 508 }; 509 510 port@a { 511 reg = <10>; 512 513 adv7482_txa: endpoint { 514 clock-lanes = <0>; 515 data-lanes = <1 2 3 4>; 516 remote-endpoint = <&csi40_in>; 517 }; 518 }; 519 520 port@b { 521 reg = <11>; 522 523 adv7482_txb: endpoint { 524 clock-lanes = <0>; 525 data-lanes = <1>; 526 remote-endpoint = <&csi20_in>; 527 }; 528 }; 529 }; 530}; 531 532&i2c_dvfs { 533 status = "okay"; 534 535 clock-frequency = <400000>; 536 537 pmic: pmic@30 { 538 pinctrl-0 = <&irq0_pins>; 539 pinctrl-names = "default"; 540 541 compatible = "rohm,bd9571mwv"; 542 reg = <0x30>; 543 interrupt-parent = <&intc_ex>; 544 interrupts = <0 IRQ_TYPE_LEVEL_LOW>; 545 interrupt-controller; 546 #interrupt-cells = <2>; 547 gpio-controller; 548 #gpio-cells = <2>; 549 rohm,ddr-backup-power = <0xf>; 550 rohm,rstbmode-level; 551 552 regulators { 553 dvfs: dvfs { 554 regulator-name = "dvfs"; 555 regulator-min-microvolt = <750000>; 556 regulator-max-microvolt = <1030000>; 557 regulator-boot-on; 558 regulator-always-on; 559 }; 560 }; 561 }; 562 563 eeprom@50 { 564 compatible = "rohm,br24t01", "atmel,24c01"; 565 reg = <0x50>; 566 pagesize = <8>; 567 }; 568}; 569 570&ohci0 { 571 dr_mode = "otg"; 572 status = "okay"; 573}; 574 575&ohci1 { 576 status = "okay"; 577}; 578 579&pcie_bus_clk { 580 clock-frequency = <100000000>; 581}; 582 583&pciec0 { 584 status = "okay"; 585}; 586 587&pciec1 { 588 status = "okay"; 589}; 590 591&pfc { 592 pinctrl-0 = <&scif_clk_pins>; 593 pinctrl-names = "default"; 594 595 avb_pins: avb { 596 mux { 597 groups = "avb_link", "avb_mdio", "avb_mii"; 598 function = "avb"; 599 }; 600 601 pins_mdio { 602 groups = "avb_mdio"; 603 drive-strength = <24>; 604 }; 605 606 pins_mii_tx { 607 pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0", 608 "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3"; 609 drive-strength = <12>; 610 }; 611 }; 612 613 du_pins: du { 614 groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0"; 615 function = "du"; 616 }; 617 618 hscif1_pins: hscif1 { 619 groups = "hscif1_data_a", "hscif1_ctrl_a"; 620 function = "hscif1"; 621 }; 622 623 i2c2_pins: i2c2 { 624 groups = "i2c2_a"; 625 function = "i2c2"; 626 }; 627 628 irq0_pins: irq0 { 629 groups = "intc_ex_irq0"; 630 function = "intc_ex"; 631 }; 632 633 keys_pins: keys { 634 pins = "GP_5_17", "GP_5_20", "GP_5_22"; 635 bias-pull-up; 636 }; 637 638 pwm1_pins: pwm1 { 639 groups = "pwm1_a"; 640 function = "pwm1"; 641 }; 642 643 scif1_pins: scif1 { 644 groups = "scif1_data_a", "scif1_ctrl"; 645 function = "scif1"; 646 }; 647 648 scif2_pins: scif2 { 649 groups = "scif2_data_a"; 650 function = "scif2"; 651 }; 652 653 scif_clk_pins: scif_clk { 654 groups = "scif_clk_a"; 655 function = "scif_clk"; 656 }; 657 658 sdhi0_pins: sd0 { 659 groups = "sdhi0_data4", "sdhi0_ctrl"; 660 function = "sdhi0"; 661 power-source = <3300>; 662 }; 663 664 sdhi0_pins_uhs: sd0_uhs { 665 groups = "sdhi0_data4", "sdhi0_ctrl"; 666 function = "sdhi0"; 667 power-source = <1800>; 668 }; 669 670 sdhi2_pins: sd2 { 671 groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds"; 672 function = "sdhi2"; 673 power-source = <1800>; 674 }; 675 676 sdhi3_pins: sd3 { 677 groups = "sdhi3_data4", "sdhi3_ctrl"; 678 function = "sdhi3"; 679 power-source = <3300>; 680 }; 681 682 sdhi3_pins_uhs: sd3_uhs { 683 groups = "sdhi3_data4", "sdhi3_ctrl"; 684 function = "sdhi3"; 685 power-source = <1800>; 686 }; 687 688 sound_pins: sound { 689 groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a"; 690 function = "ssi"; 691 }; 692 693 sound_clk_pins: sound_clk { 694 groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a", 695 "audio_clkout_a", "audio_clkout3_a"; 696 function = "audio_clk"; 697 }; 698 699 usb0_pins: usb0 { 700 groups = "usb0"; 701 function = "usb0"; 702 }; 703 704 usb1_pins: usb1 { 705 mux { 706 groups = "usb1"; 707 function = "usb1"; 708 }; 709 710 ovc { 711 pins = "GP_6_27"; 712 bias-pull-up; 713 }; 714 715 pwen { 716 pins = "GP_6_26"; 717 bias-pull-down; 718 }; 719 }; 720 721 usb30_pins: usb30 { 722 groups = "usb30"; 723 function = "usb30"; 724 }; 725}; 726 727&pwm1 { 728 pinctrl-0 = <&pwm1_pins>; 729 pinctrl-names = "default"; 730 731 status = "okay"; 732}; 733 734&rcar_sound { 735 pinctrl-0 = <&sound_pins &sound_clk_pins>; 736 pinctrl-names = "default"; 737 738 /* Single DAI */ 739 #sound-dai-cells = <0>; 740 741 /* audio_clkout0/1/2/3 */ 742 #clock-cells = <1>; 743 clock-frequency = <12288000 11289600>; 744 745 status = "okay"; 746 747 /* update <audio_clk_b> to <cs2000> */ 748 clocks = <&cpg CPG_MOD 1005>, 749 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, 750 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, 751 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, 752 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, 753 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, 754 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, 755 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, 756 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, 757 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, 758 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, 759 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, 760 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, 761 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, 762 <&audio_clk_a>, <&cs2000>, 763 <&audio_clk_c>, 764 <&cpg CPG_CORE CPG_AUDIO_CLK_I>; 765 766 ports { 767 #address-cells = <1>; 768 #size-cells = <0>; 769 rsnd_port0: port@0 { 770 reg = <0>; 771 rsnd_endpoint0: endpoint { 772 remote-endpoint = <&ak4613_endpoint>; 773 774 dai-format = "left_j"; 775 bitclock-master = <&rsnd_endpoint0>; 776 frame-master = <&rsnd_endpoint0>; 777 778 playback = <&ssi0 &src0 &dvc0>; 779 capture = <&ssi1 &src1 &dvc1>; 780 }; 781 }; 782 }; 783}; 784 785&rwdt { 786 timeout-sec = <60>; 787 status = "okay"; 788}; 789 790&scif1 { 791 pinctrl-0 = <&scif1_pins>; 792 pinctrl-names = "default"; 793 794 uart-has-rtscts; 795 /* Please only enable hscif1 or scif1 */ 796 /* status = "okay"; */ 797}; 798 799&scif2 { 800 pinctrl-0 = <&scif2_pins>; 801 pinctrl-names = "default"; 802 803 status = "okay"; 804}; 805 806&scif_clk { 807 clock-frequency = <14745600>; 808}; 809 810&sdhi0 { 811 pinctrl-0 = <&sdhi0_pins>; 812 pinctrl-1 = <&sdhi0_pins_uhs>; 813 pinctrl-names = "default", "state_uhs"; 814 815 vmmc-supply = <&vcc_sdhi0>; 816 vqmmc-supply = <&vccq_sdhi0>; 817 cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; 818 wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; 819 bus-width = <4>; 820 sd-uhs-sdr50; 821 sd-uhs-sdr104; 822 status = "okay"; 823}; 824 825&sdhi2 { 826 /* used for on-board 8bit eMMC */ 827 pinctrl-0 = <&sdhi2_pins>; 828 pinctrl-1 = <&sdhi2_pins>; 829 pinctrl-names = "default", "state_uhs"; 830 831 vmmc-supply = <®_3p3v>; 832 vqmmc-supply = <®_1p8v>; 833 bus-width = <8>; 834 mmc-hs200-1_8v; 835 mmc-hs400-1_8v; 836 non-removable; 837 fixed-emmc-driver-type = <1>; 838 status = "okay"; 839}; 840 841&sdhi3 { 842 pinctrl-0 = <&sdhi3_pins>; 843 pinctrl-1 = <&sdhi3_pins_uhs>; 844 pinctrl-names = "default", "state_uhs"; 845 846 vmmc-supply = <&vcc_sdhi3>; 847 vqmmc-supply = <&vccq_sdhi3>; 848 cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; 849 wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>; 850 bus-width = <4>; 851 sd-uhs-sdr50; 852 sd-uhs-sdr104; 853 status = "okay"; 854}; 855 856&ssi1 { 857 shared-pin; 858}; 859 860&usb_extal_clk { 861 clock-frequency = <50000000>; 862}; 863 864&usb2_phy0 { 865 pinctrl-0 = <&usb0_pins>; 866 pinctrl-names = "default"; 867 868 vbus-supply = <&vbus0_usb2>; 869 status = "okay"; 870}; 871 872&usb2_phy1 { 873 pinctrl-0 = <&usb1_pins>; 874 pinctrl-names = "default"; 875 876 status = "okay"; 877}; 878 879&usb3_peri0 { 880 phys = <&usb3_phy0>; 881 phy-names = "usb"; 882 883 companion = <&xhci0>; 884 885 status = "okay"; 886}; 887 888&usb3_phy0 { 889 status = "okay"; 890}; 891 892&usb3s0_clk { 893 clock-frequency = <100000000>; 894}; 895 896&vin0 { 897 status = "okay"; 898}; 899 900&vin1 { 901 status = "okay"; 902}; 903 904&vin2 { 905 status = "okay"; 906}; 907 908&vin3 { 909 status = "okay"; 910}; 911 912&vin4 { 913 status = "okay"; 914}; 915 916&vin5 { 917 status = "okay"; 918}; 919 920&vin6 { 921 status = "okay"; 922}; 923 924&vin7 { 925 status = "okay"; 926}; 927 928&xhci0 { 929 pinctrl-0 = <&usb30_pins>; 930 pinctrl-names = "default"; 931 932 status = "okay"; 933}; 934